is it possible to put a AWD RB26DET in a 240.. im not sure i just know a little bit about the 240sx.. but thanks to all who help!
240sx with RB26DET
is it possible to put a AWD RB26DET in a 240.. im not sure i just know a little bit about the 240sx.. but thanks to all who help!
Guys: No Shirt, No Service
Gals: No Shirt, No Charge
Full Race has done it. Check out http://www.full-race.com/r14/ for more info on it.
They will build you a chassis to accommodate the awd system or you can go ahead and have them build the whole car for you.
hell ya.. thanks i bought a 240sx for $100 and it runs but im in griffin tech for auto body and it need alot of work.. but i couldn't pass it up.. so im just going to make it a project car and put a RB26 in it.. i think.. or what would you think
Guys: No Shirt, No Service
Gals: No Shirt, No Charge
I'm to lazy to go and read the post before but from what I have heard you can run a RB26 w/ a RB25 GTS trans, so it should be do able with a few mods like custom drive shaft, mount kit, single turbo conversion (don't know if both will fit), and so on. I have never really looked into it to much. I also know that McKinney Motorsports specializes in RB swaps, so I would check them out to see if they already have a kit for the swap. The guys at Ma-Motorsports put one in a z32 no problem, so I would check them out also.
I sound kinda like a douche
ITS IMPOSSIBLE NO 240 HAS EVER HAD A RB26 OMG I HOPE YOU PULL IT OFF U MY HERO
YOu can do it for about $20000-25000 (RB26 with AWD).
A regular RB26 swap would still run $15,000ish
your best bet for a fun street car is a TUrbo KA or a SR20 swap (Under $4000)
Enterprise Data Resources- Ecommerce Project Manager
-www.usedbarcode.net
I will do the full rb26 swap for $14,999 - ish.
rb25 would be cheaper.... only .1 L less and lil older, but you can still fly like hell
so many ways to go.. damn.. thanks to everyone...
Guys: No Shirt, No Service
Gals: No Shirt, No Charge
I say not worth doing the swap, just do a rb25det, or import a gtr if you want to get a rb awd.
i say buy a different car.
LOL @ simon...
The server is too busy at the moment. Please try again later.
u drive a miata......i think u need a new 1 before he doesOriginally Posted by jesse4846
there was a rb26 swapped twin turbo S14 on the cover of super street! It was blue and it was built here in Ga. Sum dude in cummin built it for a company car!
KA-T, CA18, SR20, RB20, or RB25 are ur best options. Depends on what you want to do with the car, and what budget your budgets it.
TS240... i just want to drift a lil here and there and drag.. but its my project car so im going all out.. but whats best for the money thats still a beast..
Guys: No Shirt, No Service
Gals: No Shirt, No Charge
2jz.
are bee what?
And that just happened.
'92 C2500 6.5 Turbo Diesel | '96 240sx
hahahahahahahaha... 240s are gay....
dammit I have a 240. ****.
Fuck stance. Stance is for kids in skinny jeans with Justin Beiber haircuts. You don't need stance when you got swagger.
if you want to drift a little here and there...KA-T's gonna be the best option
if your wallets a tad thicker, go SR20.
if you wanna be semi-unique; CA
price of RB26 swap = enough for a WRX or something higher up.
Ok if ur going all out we can scratch KA-T off the list. We can also forget about a CA18, they are great for drifting and road racing when their built but not for drag racing.
So that leaves us with the SR, RB20, RB25, and 2JZ(if ur mad balling).
SR's and RB20 I think make about the same power, but an RB feels a lot more torquey. SR's are good engines with a lot of after market support, they are propably the most common swap you'll see.
Now lets take for example you wanna use the stock motor and just get boltons, a bigger turbo, bigger injectors, an engine manigment system, and a boost controller. I would recomend an RB it should be more relaiable for the higher horsepower demands. (Not to say an SR couldn't handel these demands just fine.)
An RB25 is a more exspensive alternative but it'll put down a good amount of power. A 2jz would be the F**king awsome but the sawp cost right around $10,000.
I would say ur best bet would be an SR or an RB20.
Im no expert by any means this is just my
You might should as Mr.Kidd or Hell-Fire they know their ****.
CA over SR any day for reliability and nice high rev limiter.
But for cost these days... RB20 all the way. 1200 dollars or less for the motor you cant beat that
Honda RC51 SP1
Yoshi RS-3 Cans
520 Conversion
Clip Ons
Race Tech Fork Kit
lolz thats what i said
lolz at dustin's comment... hahahahha
Why?? Explain reasoning.
Last edited by Nick; 11-21-2007 at 06:55 AM.
Haha... 4 and 6 cylinder motors..... hahahahahahahahahahaha.
Seriously people... think outside the box.
Fuck stance. Stance is for kids in skinny jeans with Justin Beiber haircuts. You don't need stance when you got swagger.
where the heck did you buy one for $100?
my friend.. but something just came up.. i might be moving to flordia for 3 years for my job.. so i might sell the car now.. so if i do you can starts making offers..
::REMEMBER:: its a project car.. need work mainly body work.. but will sell for cheap
Guys: No Shirt, No Service
Gals: No Shirt, No Charge
I give you what you paid for it.........
If you keep it, why not give it the 350z/G35 drivtrain? Would be different, and can be easily turboed, and would be some sick ****.
Kevin
LOL! MIATA BUY A REAL CAR!!!!!
I do rb20 and rb25 wiring into s13 and s14's 300.00 shipped 24hr turn around turn ket start guaranteed! PM me for more details!
I'll give you twice what you paid for it
I worded that wrong.
Nothing against a KA-T Im actually half way through build one. (forged internals etc.)
My problem with a KA-T is to make a really nice reliable one it cost a ton. I've got the cost of an RB25 in my motor already and I havent even purchased the turbo componets I wanna use.
Like I said thats just my opinion, Im not an expert and I don't claime to be one.
Posting Permissions
Reply With Quote
