Results 1 to 9 of 9

Thread: clutch cyl or slave cyl???

Hybrid View

  1. 11-05-2006, 09:18 PM #1
    2.3 Evo 8
    Guest

    Default clutch cyl or slave cyl???

    My clutch pedal has been acting up since 2 days ago by completely going to the floor and I would have to put my foot behind it and pull it back out.

    I would pump it and then it would be fine for a few minutes and then do it again.

    Last night it went out completely. No more pedal at all. We bled the clutch line with no luck.

    Is it the slave cylinder or master cylinder and how can you tell?
    Reply With Quote Reply With Quote
  2. 11-05-2006, 11:48 PM #2
    bluuuurr
    bluuuurr is offline
    Certified Gearhead bluuuurr's Avatar
    Join Date
    Oct 2003
    Location
    Monterey, CA
    Age
    42
    Posts
    658
    Rep Power
    22

    Default

    slave cylinder.. the master cylinder is for your brakes.
    Reply With Quote Reply With Quote
  3. 11-06-2006, 02:38 AM #3
    Flip
    Flip is offline
    My Spoon Is Too Big! Flip's Avatar
    Join Date
    May 2003
    Location
    Marietta
    Age
    43
    Posts
    7,979
    Rep Power
    31

    Default

    Quote Originally Posted by bluuuurr
    slave cylinder.. the master cylinder is for your brakes.
    Thats wrong...

    Just as the above post said there is a master cyl. that is attached right behind the petal...

    Have you seen any fluid leaking? Is the fluid level going down at all? If not that means there is still air in the lines somewhere... I know on my 240 there is a speed bleeder valve with an extra length of hose that when air gets in it is REALLY hard to get it out. I am opting to just remove the speed bleader to avoid that problem...

    Also, did this just come on randomly and immediately? or was there something that brought it on?
    Reply With Quote Reply With Quote
  4. 11-06-2006, 02:52 AM #4
    2.3 Evo 8
    Guest

    Default

    Quote Originally Posted by bluuuurr
    slave cylinder.. the master cylinder is for your brakes.
    You sir are an idiot! Don't give advice when you don't know what the fuck your talking about.


    We found the problem and it wasn't either. There was a very small leak on one of the lines that was barely visable and we temporarily fixed it.
    Reply With Quote Reply With Quote
  5. 11-06-2006, 03:37 AM #5
    Flip
    Flip is offline
    My Spoon Is Too Big! Flip's Avatar
    Join Date
    May 2003
    Location
    Marietta
    Age
    43
    Posts
    7,979
    Rep Power
    31

    Default

    Quote Originally Posted by 2.3 Evo 8
    You sir are an idiot! Don't give advice when you don't know what the fuck your talking about.


    We found the problem and it wasn't either. There was a very small leak on one of the lines that was barely visable and we temporarily fixed it.
    ^ what i figured good deal...
    Reply With Quote Reply With Quote
  6. 11-06-2006, 01:30 AM #6
    b17a1db2
    b17a1db2 is offline
    ...
    Join Date
    Apr 2006
    Location
    Augusta, GA
    Posts
    1,389
    Rep Power
    21

    Default

    there is a master cylinder for your clutch too right behind the pedal.
    Reply With Quote Reply With Quote
  7. 11-06-2006, 09:21 AM #7
    §treet_§peed
    §treet_§peed is offline
    A.D.I.D.A.S. §treet_§peed's Avatar
    Join Date
    Dec 2005
    Location
    Gainesville
    Age
    38
    Posts
    24,950
    Rep Power
    49

    Default

    Duct tape ftw?
    You know better; next time will be a ban.
    Reply With Quote Reply With Quote
  8. 11-06-2006, 09:23 AM #8
    2.3 Evo 8
    Guest

    Default

    teflon tape ftw!

    ...but we didn't use it on the threads, lol.
    Reply With Quote Reply With Quote
  9. 11-06-2006, 09:27 AM #9
    §treet_§peed
    §treet_§peed is offline
    A.D.I.D.A.S. §treet_§peed's Avatar
    Join Date
    Dec 2005
    Location
    Gainesville
    Age
    38
    Posts
    24,950
    Rep Power
    49

    Default

    werd lol
    You know better; next time will be a ban.
    Reply With Quote Reply With Quote
« Diiferential, both bearings failed, Help? | CAI tips ? »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

About us
ImportAtlanta is a community of gearheads and car enthusiasts. It does not matter what kind of car or bike you drive, IA is an open community for any gearhead. Whether you're looking for advice on a performance build or posting your wheels for sale, you're welcome here!
Announcement
Welcome back to ImportAtlanta. We are currently undergoing many changes, so please report any issues you encounter with the site using the 'Contact Us' button below. Thank you!