crower cams what to degree them too??

[jap_racer1]

I have a set of stage 2 n/a cams they are part number 63402a-2 i am trying to figure out what to degree them to i have aem cam gears so does anyone have a way to point me to find the specs so i can just turn the cams and set them retarded or advanced??

[scttydb411]

like i said before on the phone...the only real way to do it is w/ a degree wheel and the specs of the cam. if crower will give you the settings (they usually won't) that can be a place to start. the only cams i know of that give good starting settings are skunk2 and they are pretty close. they only problem is when there has been some shaving/milling of head/block and/or major variations in the setup from the original tested engine.

the only people i would trust on this would be crower...2nd would be someone physically degreeing them in with specs in hand.

[scabtastic]

yeah every other forum ive been on the general consensus on this is with the degree wheel.

[jap_racer1]

like i said before on the phone...the only real way to do it is w/ a degree wheel and the specs of the cam. if crower will give you the settings (they usually won't) that can be a place to start. the only cams i know of that give good starting settings are skunk2 and they are pretty close. they only problem is when there has been some shaving/milling of head/block and/or major variations in the setup from the original tested engine.

the only people i would trust on this would be crower...2nd would be someone physically degreeing them in with specs in hand.

O i believe you sctty i tried crower they said i have to use a degree wheel the only thing is i have no way to get that dont by saturday?? i aint ever messed with that kinda stuff so i dont want to bother with it untill i learn so ???

[BABY J]

Blox cams come w/ that info on the cam card as well. Are you SURE there is no documentation in the box? I'm pretty sure there should be unless u bought then used.

[jap_racer1]

no they come with info for a degree card but it doesnt tell you the exact degree just to turn the cam gears too soo i am prolly gonna pay mainstream to do it!!

[VickNotic]

i've had these before, pretty aggressive i'd say but i 4got what degree mines was in but i just didn't care bout the degress i just slipped them on ! and bam bamm bamm Boomm i was on the road under 2years and sold them.. never had a chance to tune them..! biGG difference i tell ya .. but ion if it's the same as mines my was the 402a the N/A application

[jap_racer1]

yeah same ones but i am in a slight built GSR bottom and up so i am getting it tuned i am already tuned on some shitty cams but i am upgrading all the way around!!

[scttydb411]

call me when you find out what day you're off next week...hopefully it's mon-wed. otherwise, we can work something out for mon-wed of the following week.

[jap_racer1]

OK everything is together and we got something going now!! I have
GSR bored to 82mm with PR30 pistons
stock rods and crank
ACL race bearings
Stock GSR head after the ported one cracked
i have dual springs unknown name
titanium retainers
crower cams stage 2 N/A
AEM CAM GEARS for a tru time
ctr header
cold air
260cc venom injectors might switch to 440's
Holley 255 lph fuel pump

[BABY J]

So you went w/ RACE bearings? Is this going to be a DD? If so I'd save those and just get the ACL non-race bearings. Also --- why not hold off for some different rods? And are the PR30 pistons 82mm??

[ash7]

BabyJ is right.

-jonathan

[BABY J]

Also --- stock injectors will be just fine.

[ash7]

BabyJ is still right.

-jonathan

[boosted b]

Yeah why would u change injectors stock can hold 200 hp

[jap_racer1]

stock can hold 185 i have 260cc in there a set of stock at the house and a set of 440cc in my back seat i think i am good got it tuned something aint right only 163whp 124wtq

[BABY J]

Answer my questions please. This block is overbored to 82mm right? What bore are your PR30 pistons??

[scttydb411]

stock can hold 185 i have 260cc in there a set of stock at the house and a set of 440cc in my back seat i think i am good got it tuned something aint right only 163whp 124wtq

dc 4-2-1 header
stock cat
short ram
stock intake manifold

might be the issue

[BABY J]

Well he'll see more peak w/ the short ram and less TQ (vs a longtube) - but there are so many holes in this thread that I am getting tired of trying to help him.

[i4_garage]

i think i have these cams in my itr...NA stage 2 stock idle lobe?
It hits vtec hard and idles like a stock car

[scttydb411]

Well he'll see more peak w/ the short ram and less TQ (vs a longtube) - but there are so many holes in this thread that I am getting tired of trying to help him.

on the dyno, yes. close the hood on the road and iat go up killing power.