getting it tuned
Ok i am wanting to get my engine tuned and i am just trying to figure out what all they do in a tune. I figure if it is just the basics plugs wires cap ect. I can do all that myself but i am just wanting to know if there is more to it. I am only doing 147 on the dyno right now and i know i can get at least 10 more.
FUN FUN FUN
MI-4
what motor, what car, need more info.
Enterprise Data Resources- Ecommerce Project Manager
-www.usedbarcode.net
97 honda civic EX
b16a, ferra valvetrain, sir 2 cams, b16a2 intake manifold, JE pistons, eagle rods, spoon flywheel, jdm gsr tranny, chipped p28
that all u need?
Last edited by nooneimportant; 04-06-2005 at 08:50 AM.
FUN FUN FUN
MI-4
No tuning is a lot more in depth that a tune up. They will basically alter the fuel map/timing through out the rpm band to produce the most horsepower and compliment your build. That is why there is dyno time normally involved. Atleast I am pretty sure that is the bulk of it, I am still tired this morning and half asleep :p
Last edited by GA_Teg; 04-06-2005 at 09:37 AM.
ferrea valvetrain- do you have their flat faced valves? that would mean a raise in compression. the intake manifold is stock, so thats no big deal, what kind of JE pistons, what compression level 10.5:1,11:1,11.5:1 etc? do you have the A beam or H beam eagle rods?Originally Posted by nooneimportant
If you dont have at least VAFC then its worthless. PM me for more information. The cams are weak and so is the intake manifold, those are the problems with your setup, you running shitty cams and a stock intake manifold. i would look at getting CTR cams and a AEBS intake manifold. the dynos i have done i have seen the power band extend 800rpms on a b16 with just the AEBS.
PM me or VTECKIDD on aim
Enterprise Data Resources- Ecommerce Project Manager
-www.usedbarcode.net
sounds good man i guess i can't do it myself i wish battlegrounds would be able to do it this weekend but i guess they are all booked up this weekend that sux. Got to wait a couple more weeks. Ne one know someplace down neer Valdosta area that do a good job and have a dyno?
FUN FUN FUN
MI-4
my shop cna handle Uberdata,crome,BRE, and VAFC tuning, ill be Hondata operational by mid april
Enterprise Data Resources- Ecommerce Project Manager
-www.usedbarcode.net
where this shop at?
FUN FUN FUN
MI-4
we are located in powder springs.
Last edited by vteckidd; 04-06-2005 at 12:43 PM.
Enterprise Data Resources- Ecommerce Project Manager
-www.usedbarcode.net
yo vteckid u know anything about sr20? hit me up on aim flysi00 or pm me
just got a typhoon aebs intake manifold for it but kinda to broke to get cams right now got to wait till pay day.
FUN FUN FUN
MI-4
thats fine, i would put the manifold on and wait to get some cams before tuning it. get a VAFC or uberdata as well.
Enterprise Data Resources- Ecommerce Project Manager
-www.usedbarcode.net
i think i met you one sat night,on pleasant hill, i hade the white EG hatch with the cage in it, i was talking to shawna
Enterprise Data Resources- Ecommerce Project Manager
-www.usedbarcode.net
yea u probably did i don't know i got a white civic EX
FUN FUN FUN
MI-4
I have looked into a VAFC and may be gettin one in the near future i just would need to have someone show me how to install ad use it.
FUN FUN FUN
MI-4
its not hard, we charge $75 to install it
Enterprise Data Resources- Ecommerce Project Manager
-www.usedbarcode.net
i like to do everything myself i just need to have someone tell me how to do it but that won't be for awile.
FUN FUN FUN
MI-4
if you can [properly] wire up a stereo then you shouldn't have a problem with a v-afc...just get the diagram(s) from A'pexi's site and sometimes you have to cross reference it with another diagram to match your car (normally only with a swap)
yea true true ill be doing that inawile tho
FUN FUN FUN
MI-4
Posting Permissions
Reply With Quote