Results 1 to 9 of 9

Thread: im having a little trouble...

Hybrid View

  1. #1
    Certified Gearhead Drake's Avatar
    Join Date
    Apr 2007
    Location
    Fayette-nam.
    Age
    37
    Posts
    212
    Rep Power
    19

    Default im having a little trouble...

    getting the starter off of my S13.

    suggestions?

    and how would i go about swapping one 5spd transmission to another 5 spd transmission?

    if you can help i'd mucho appreciate it.
    1990 cb7: grocery rocket

  2. #2
    Barefoot Motorsports
    Join Date
    May 2003
    Location
    jonesboro
    Age
    42
    Posts
    7,939
    Rep Power
    36

    Default

    first tip is to get u a manual.



    * Remove clutch operating cylinder from transmission.
    * Disconnect speed sensor, O.D. position switch, top (4th) position switch, reverse lamp switch and neutral position switch harness connectors.
    * Remove starter motor from transmission.
    * Remove propeller shaft. - Refer to section.
    * Insert plug into rear oil seal after removing propeller shaft.
    * Be careful not to damage spline, sleeve yoke and rear oil seal when removing propeller shaft.
    * Remove exhaust tube mounting bracket from transmission.
    * Support manual transmission with a jack.
    * Remove rear mounting bracket.
    * Lower manual transmission as much as possible.
    * Remove shift lever with control housing from transmission.



  3. #3
    I Am, A Stunt Man
    Join Date
    Mar 2008
    Location
    Douglasville, Georgia, United States
    Age
    37
    Posts
    3,502
    Rep Power
    22

    Default

    yes, let hanes, or chilton be your best friend, and where are you located? buy my friend and i some food and drank, and we will help, if you are close around

  4. #4
    Photography & Design
    Join Date
    Sep 2007
    Posts
    4,485
    Rep Power
    27

    Default

    2nd tip is to buy a 240z

    NIKON Squad | D90

  5. #5
    Certified Gearhead Drake's Avatar
    Join Date
    Apr 2007
    Location
    Fayette-nam.
    Age
    37
    Posts
    212
    Rep Power
    19

    Default

    thx kev. now how about that starter? haha
    1990 cb7: grocery rocket

  6. #6

    Default

    Quote Originally Posted by Drake
    thx kev. now how about that starter? haha
    There are 2 bolts that hold the starter on. they run from the back of the car to the front through the bellhousing into the starter. Then disconnect the wiring from the starter and it will just fall out.


    Custom Tuning By Daniel Willie.
    Parts, Fabrication, Race Car Prep
    770-319-9605 or [email protected]

  7. #7
    Certified Gearhead Drake's Avatar
    Join Date
    Apr 2007
    Location
    Fayette-nam.
    Age
    37
    Posts
    212
    Rep Power
    19

    Default

    thanks yall. reps to all!! now if i can just get that dern tranny out..
    1990 cb7: grocery rocket

  8. #8

    Default

    Quote Originally Posted by Drake
    thanks yall. reps to all!! now if i can just get that dern tranny out..
    LOL, it cant be hanging in there by much.


    Custom Tuning By Daniel Willie.
    Parts, Fabrication, Race Car Prep
    770-319-9605 or [email protected]

  9. #9
    Certified Gearhead Drake's Avatar
    Join Date
    Apr 2007
    Location
    Fayette-nam.
    Age
    37
    Posts
    212
    Rep Power
    19

    Default

    lack of time and manpower. delivering pizza for a hole in the wall place in a f150 is killer, i miss the 2-4.
    1990 cb7: grocery rocket

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
ImportAtlanta is a community of gearheads and car enthusiasts. It does not matter what kind of car or bike you drive, IA is an open community for any gearhead. Whether you're looking for advice on a performance build or posting your wheels for sale, you're welcome here!
Announcement
Welcome back to ImportAtlanta. We are currently undergoing many changes, so please report any issues you encounter with the site using the 'Contact Us' button below. Thank you!