Adding oil to a Manual Transmission.

[BIG WORM]

On an integra.

Can I pour it in through the speed sensor?

or does it have to be done from the bottom?

REPS for replys.

[NEMO]

On an integra.

Can I pour it in through the speed sensor?

or does it have to be done from the bottom?

REPS for replys.

you can add it through where the speed sensor is located(dont forget to take the speed sensor out )

[BIG WORM]

yeah that's what I meant.

you can add it through where the speed sensor is located(dont forget to take the speed sensor out )

[NEMO]

yeah that's what I meant.

yeah thats how i added mine.

[aaronfelipe]

x2

[gsrteg]

do it the proper way...use a funnel and tube, and theres a bolt to fill, and a separate bolt to drain.

[Barefoot]

do it the proper way...use a funnel and tube, and theres a bolt to fill, and a separate bolt to drain.

why do it that way. its more of a head ache. the speed sensor is just so much easier while still being just as accurate.

[NAIZBST]

remember to fill up with 2.3 quarts

[LIKEG6]

use the funnel and hose technique

Near the cv axle there is a fill hole just put a 17mm on the bolt and pull it out stick in the hose and run it to the top. Then stick your funnel in it and fill until it starts to overflow

[j0nbunklah0m]

^^ i just changed my tranny fluid today as well. i wish i woulda seen this thread earlier lol

[NEMO]

use the funnel and hose technique

Near the cv axle there is a fill hole just put a 17mm on the bolt and pull it out stick in the hose and run it to the top. Then stick your funnel in it and fill until it starts to overflow

why do it the hard way?

[scttydb411]

at least pull the fill bolt out to see when you've got too much. you risk overfilling it through the speed sensor hole. if you overfill the oil will seep out the output shaft and soak your clutch/pp.

[T34me]

yeah, if it was meant to fill throught the top, they would not have drilled the extra fill hole, just do it the right way.

[Vteckidd]

drain, fill with 2 quarts. YOu cant overfill if it you only use 2 quarts

/thread

[Barefoot]

yeah, if it was meant to fill throught the top, they would not have drilled the extra fill hole, just do it the right way.

not even honda is perfect.

[GSRteg®]

remember to fill up with 2.3 quarts

X2

[LIKEG6]

why do it the hard way?

lol

the right way is not always the easiest

[southside]

Its a headache doing it from the bottom but it is the right way...Make sure you put down a piece of cardboard I spilt alot of oil due to improper tools..

[csmiths]

just fill it in the fill plug its not that hard to do, and your already right there to drain it out. so.....

[Tech5]

What I do is drain with the 3/8 ratchet bolt and take the 17mm bolt out up top , screw the 3/8 bolt back in tighten it, and then take the 1 10mm bolt out of the speed sensor wingle it back an forth an remove it, fill the fluid until it runs out of the 17mm hole then install the 17mm bolt and gentle install the speed sensor and line up the hole and install the 10mm bolt and your done, whip off fluid and clean up your done!

Fluid I use either, Honda/Acura fluid which cost 5.49 qt
or GM syncro mesh!!!

[NEMO]

What I do is drain with the 3/8 ratchet bolt and take the 17mm bolt out up top , screw the 3/8 bolt back in tighten it, and then take the 1 10mm bolt out of the speed sensor wingle it back an forth an remove it, fill the fluid until it runs out of the 17mm hole then install the 17mm bolt and gentle install the speed sensor and line up the hole and install the 10mm bolt and your done, whip off fluid and clean up your done!

Fluid I use either, Honda/Acura fluid which cost 5.49 qt
or GM syncro mesh!!!

[Stormhammer]

2 quarts? good god my tranny takes almost 4-5...

[Tech5]

well buy a honda or stop biatching!

2 quarts? good god my tranny takes almost 4-5...