Printable View
looks like the start..mayb little shinnier?
http://i74.photobucket.com/albums/i2...1/CIMG1006.jpg
http://i74.photobucket.com/albums/i2...1/CIMG1007.jpg
shows where i stoped the color and then cleard..so didnt do too much?
http://i74.photobucket.com/albums/i2...1/CIMG1008.jpg
If the whole car was that flat blue color, it would be cool.
^ thats what im looking at.lol the bumpers,side skirts and roof are all slick and shinney now.. and spoiler :(
haha
sitting outside..drying..still kinda gummy;
http://i74.photobucket.com/albums/i2...1/CIMG1009.jpg
http://i74.photobucket.com/albums/i2...1/CIMG1010.jpg
http://i74.photobucket.com/albums/i2...1/CIMG1012.jpg
color dose not match..ha
http://i74.photobucket.com/albums/i2...1/CIMG1013.jpg
now this i did last night,no clear;almost the same apperance.
http://i74.photobucket.com/albums/i2...1/CIMG1014.jpg
I bet your neighbors hate you.
I like it that color...lol
on one side,its full of mexicans painting it and redoing it for sale at the moment..other side,they like watching me always change the car.ha iv died down on doing loud things for a while..but ya the compressor is kinda loud and annoyying.Quote:
Originally Posted by Init2winit
ha appreciate it..atleast its better than having blue car and a dark gray door.haQuote:
Originally Posted by simontibbett
i didnt take a before shot of my car with the new doors..but heres my old doors on his car.now driving around Tampa,FL,
Guy drove down from Tampa to swap doors and get his side skirts put on.:crazy:
http://i74.photobucket.com/albums/i2...11/olddoor.jpg
try putting more clear down, it looks like you are just not putting enough down for it to level out. also, how much CFM does your compressor put out. If its not enough then it will just sputter the clear and not atomize it correctly. Most HVLP's require atleast 7-8 CFM usually more. My DeVillebliss uses over 10 when i turn it up. Also check your pressure drop when you are spraying. If you set the regulator at 25 you may only have 18 at full depression.
Hope this helps
kyle
im using a Brut 10gallon 2.5hp compressor, its 125psi max..
90psi 5.1...and 40psi at 4.1 (what it says on tank.lol)
and have the gun all the way open 50max,,then running the reg.and gauge reads 25psi.then 40 when i was doing clear.
where do you live?
Lilburn,GA
turn your pressure down a bit, most HVLP's max out at 35. so i would try 30 especially if you have it all the way open. You may want to shoot a little less for the clear. I think you are just shooting too high of a pressure. If Bucky is close enough too you, you might want to pay him some gas money to come help you. I am further than he is. Or if you want to stop by the shop one day i can show you a few things. Some of the tips are hard to explain, and better to show in person.
kyle
i am near 316 and 20 how far is that from you
ok appreciate it..
like iv said,i quit my job last week..so i have no money now.ha trying to sell some car parts.
ill be willing to trade my 12"kicker L7,box and amp for some good clear and little cash.ha
http://www.importatlanta.com/forums/...d.php?t=184868
Pm'dQuote:
Originally Posted by The BUCKY
but im about 30ish mins from mall of GA
You misted the clear coat?!?!!?!
no-the 1st 3 coats i did medium wet (6-8") away like directions..then it said final coat hold gun 9-12" away for metallic paints...
ohhhh you misted the BASE coat ok ok. Yea thats normal to do with metallic base coats, if you dont have a special tip on your spray gun for metallics.
its the same gun my uncle sprayed his pearl white beretta with along time ago...1.4mm tip..
yea, usually painters spray metallics/pearls with 1.3.
and a lot of profession spray guns (anest Iwata/SATA) all have special air caps for metallics.
this is what it turned out looking like after i buffed it the last time(last week)..its kinda hard to explain what it looked like..you can see from the pic.
now when i go get some new clearcoat..would i just scotch gray-pad to scuff it up to reclear?
http://i74.photobucket.com/albums/i2...CIMG0992-1.jpg
Looked like crap..textured flat blue looked better than that...haha:(
Yea take a bucket of water, a grey scotch pad and do it while it is wet. And if you want get some PPG scuffing paste too, to quicken the process. and then wash the car down with some dish washing soap, let it dry tape off and re-clear if you didn't go through the base.
BUt from looking at that texture, it looks as if you can feel it too. If so you might want to wet sand with 1k and then spray the clear. Don't bear down too hard and go through the base either, because I'm assuming your running low on the blue.
Some will tell you to just scotch pad it, but the texture will still be there, and when you re-clear it you wont feel it but the clear will maginify the texture so it will look as if it is orange-peeled/dry sprayed.
Good luck.
ya i have little less than half a quart on blue now..since iv reprayed both sides 2times now..
i didnt put clear on my passenger side the other night,so what should i do about that? and it has high texture..
I have room to sand down the drivers side since i put 3coats of that duplicolor clear on..but the other night when i tryed to reduce the texture it didnt work,so i got pissed and put everything away and never cleared it..
It should be fine, but without clear coat the base will be more prone to chips and scratches.
Before you reclear that fender, make sure you wet sand with 1k before you reclear.
Bring your gun to me, and i'll set it for you, i don't think the gun is set up correctly if your getting that much texture.
Pm'd
here are some pics i took...to kinda show what im working with..
*note bumpers,spoiler have not been wetsanded or buffed and still look decent...:(
Pass. side,NO clear, pretty textured..
http://i74.photobucket.com/albums/i2...1/CIMG1017.jpg
Drivers side.3 coats of clear,minimul texture..
http://i74.photobucket.com/albums/i2...1/CIMG1019.jpg
Quarter and rear bumper comparsion..
http://i74.photobucket.com/albums/i2...1/CIMG1018.jpg
VQ35 Star i meant to say bufford hwy is NOT too far away..lol sorry
pm me your address. i will see how far it is
Pm'dQuote:
Originally Posted by The BUCKY
RUN SOM REDUCER THROUGH YOUR GUN WITH OUT ANY AIR HOSE AND SE IF IT COMES OUT IN A STEADY STREAM. IF NOT A STRAIGHT STREAM THEN GUN IS CLOGGED. SRRY BOUT CAPS. also b sure theres no moisture in the air when doing base and you can wait between coats. now the clear can b done anytime after base is layed down and do a light coat then a medium then a kinda heavy coat on the paint and clear. but on clear wait between coats till you can touch an oversprayed area and touch finger and thumb 2 gether and laeve a sticky trail kinda like bubble gum from the 2 fingers and then within a cpl mins start next coat. then let set all night and about 12 or so hours later water sand with 1000 grit. this is colorsanding. then get some 3m extra cut buffing compound and a godd multispeed buffer and buff till no sand scratches are visible. this takes the longest but must be done within 24 hrs. then if the paint hazes later buff untill paint no longer hazes.
all base coats turn dull as they dry also.
turbob20, lol I think he knows how to paint, hes just wondering why hes getting the texture. But thanks on the text book answer.
well its poor boy text book but hey if he knew how any real painter would figure out you get what you pay for in this business, and we all have to cut them corners sometimes.
turbob20 i can vouch for he painted my car and its clean
Sorry Bucky and everyone else;I got bored and decided to try it..
-well i got gloss,BUT HELLL load of Orange peel.I MEAN HELL alot...ill be having fun blocking this out by hand tmr or when ever..:goodjob:.
Used the Smart-4:1 with medium activator..
this is about 5coats so i dont go through sanding all this out..ha
**dosnt even look like 5 either**
http://i74.photobucket.com/albums/i2...1/CIMG1128.jpg
http://i74.photobucket.com/albums/i2...1/CIMG1129.jpg
http://i74.photobucket.com/albums/i2...1/CIMG1130.jpg
http://i74.photobucket.com/albums/i2...1/CIMG1131.jpg
hey dude, play around with your air settings on the gun, it seems like its not atomizing correctly, and also, what kind of reducer are you using? i got some clear and reducer that i will sell you if you want that i got left over from my paint job when i was spraying at the spray glo. send me a pm if you want some more help, ill be in suwanee this weekend if you want me to come over and help you. also, what gun are you spraying with?
Ya i tyred differnt settings each coat.ha
But no thanks i have almost the full gallon left,and most of the activator.it looks alot better out in the sun.metallic shows really well. i just have to buff it to slick it out now.
This mainly was a CHEAP spray to have 1 color car instead of silver doors.so i pretty much got what i needed out of it.