clutch is GONE
I gotta 92 Teg. . .i put it in first gear. . .let off the clutch and it won't even stall. . .first guess is that the clutch is FUUU:idb:EEED. . .someone recommend a sponsor that'll do it for the low or. . .if any of you have a cherry picker for sell (engine hanger) for sell. . .i'll risk sweat, blood and balls to do it myself.
you dont need a picker to pull the motor to do a clutch just pull the wheels and axles and have at it... you just need a jack so you dont drop it on the ground.
The G Spot Hero
"Nitrous is like a hot girl with STDS, you know you want to hit it but your afraid of the consequences."
DAmn what a relief. . .hahahah. thanks +reps ..
is there a certain procedure to it. . any precautions you can give me.
dont drop it on your foot?... i figure its like any FWD. wheel axles... maybe lower center subframe strap slid trans out on a angle to clear the from frame rail... i deal with nissans and thats how we do it.Originally Posted by seniosoul
The G Spot Hero
"Nitrous is like a hot girl with STDS, you know you want to hit it but your afraid of the consequences."
would i have to replace flywheel and pressure plate also. . .or will replacing clutch fix the problem itself? sorry bout the ?'s they just keep piling.
depends on if you cooked the flywheel but i always replace the p-plate with a clutch and throw out bearing
The G Spot Hero
"Nitrous is like a hot girl with STDS, you know you want to hit it but your afraid of the consequences."
chances are it's likely that your flywheel might need to be resurfaced...
and if you were thinking you needed a picker to pull the motor... just to do a clutch.. you might wanna have someone else do it.
no offense.
but really.
ohh and as far as choosing another clutch. exedy ftmfw!
you can buy an engine hoist for like $150 bucks. Or take it to a shop and get it done properly for a few hundred.I gotta 92 Teg. . .i put it in first gear. . .let off the clutch and it won't even stall
The Carbon Fibered R6
is it possible to do it without an engine hoist. . .cause i'm not trying to spend money i don't have.
yea it is. either have a lift and trans jack or take ur chances on trying to lay it on your chest or dropping it on the ground softly.
my .02¢.....let a pro do it.
The Carbon Fibered R6
he could us a floor jack...
but still if you dont know what your doing. let someone that has done it a few times to either help or do it for you.
The G Spot Hero
"Nitrous is like a hot girl with STDS, you know you want to hit it but your afraid of the consequences."
yea u could but with a...this is a honda right?...that round ass tranny will prob roll over and sqaush him if he doesnt strap it right.
The Carbon Fibered R6
eh yeah dont know hondas. like it said nissan im game
The G Spot Hero
"Nitrous is like a hot girl with STDS, you know you want to hit it but your afraid of the consequences."
i got exedy clutch disc for $40 and ill bring it to you since your immobile
just gimme ur engine n tranny
bring your car to me and ill do a clutch swap for a certain price
you should take this deal
look in the sponsor section. Vuong's Garage Charges $230 starting for labor to replace a clutch... it may be a little more depending on the amount of hours it takes....just check out the sponsor section
Since it's my first car and all. . .I'mma ride till it DIE. . .by then i'll hope to have enough money to get another Og teg thats way betterjust gimme ur engine n tranny. . .not possible to become a baller over night all by your lonesome
Patience is a Virtue
ATL DA SQUAD MEMBER #27
All you need is a basic tool set a good floor jack.
10, 12, 14, 17, 19, 36 mm sockets/wrenches. A few extensions, punch, hammer, etc. Very basic stuff.
"Cool car" less.
Anti-Nutswingers Crew - Member # 001
Posting Permissions
Reply With Quote
