Damm man!! Nice work and very detailed!!
I just take off and hop i know where it all goes when i put back toghter!!
Your doing a awesome job!! If u need any help or idea let me know!!
Printable View
Damm man!! Nice work and very detailed!!
I just take off and hop i know where it all goes when i put back toghter!!
Your doing a awesome job!! If u need any help or idea let me know!!
bunch of worthless pictures
Thanks guys for the feedback.
Today was 70+ degrees and not a cloud in the sky. So I spent some time in the garage :bump: I removed the GC/Koni's from the rear and installed the OEM suspension. Once the suspension was installed I rolled her outside:
http://i121.photobucket.com/albums/o..._3456_rs23.jpg
Time to start removing $hit so I can start prepping for paint :cheers:
Charcoal canister OUT:
http://i121.photobucket.com/albums/o..._3465_rs23.jpg
To bring the wire harness back into the car you'll need to remove the grommet by pushing or pulling it from the hole:
http://i121.photobucket.com/albums/o..._3490_rs23.jpg
Everything fit through the hole to get back into the cabin:
http://i121.photobucket.com/albums/o..._3493_rs23.jpg
Most likely going to remove this dead weight and rewrap the harness:
http://i121.photobucket.com/albums/o..._3495_rs23.jpg
Push the drivers side grommet into the cabin and reel the harness in:
http://i121.photobucket.com/albums/o..._3499_rs23.jpg
Back of the EGR valves:
http://i121.photobucket.com/albums/o..._3501_rs23.jpg
I had no intention of removing the brake lines, but after easily breaking the first line.... there was no turning back:
http://i121.photobucket.com/albums/o..._3508_rs23.jpg
Removing the master cylinder:
http://i121.photobucket.com/albums/o..._3523_rs23.jpg
I need to figure out how to remove these lines that go to the rear of the car:
http://i121.photobucket.com/albums/o..._3536_rs23.jpg
How she sits at the end of today:
http://i121.photobucket.com/albums/o..._3535_rs23.jpg
What I removed today (yes the brake lines are labled to where they go) :screwy: :
http://i121.photobucket.com/albums/o..._3540_rs23.jpg
I didn't get a chance to clean her up :no: Got to get the brake booster out, rest of the lines, and slave cylinder. Then I'll start prepping the bay for paint : :cheers:
Just crazy!
wow man u are definately a very careful guy. +1 for ziplock bags
dude. i have done these type of work, and props to u for doing it .... i know its alot alot alot of work ... lol....oh btw. the brake lines that goes to the back...u have to remove them from the back then lower the wntire thing....and also when paiting ur bay....remove the cross member and subframe as well....might as well :)
Keep up the good work.. and keep updating...
lol yeah i can 2nd that... its alot of work... better off just taping off and coving off the lines that run to the rear if you dont want to remove then...ive helped Li a few times and you should drop the subframe when you paint it... it helps you get every last sppot....Quote:
Originally Posted by _/[)/\/\ __ //_ ][
Thanks for the info guys about removing the lines and subframe :goodjob:
No work since last post, but I did scoop some supplies that should be very helpful:
This is what I will be using to keep the metal edges from touching any wiring:
http://i121.photobucket.com/albums/o..._3718_rs23.jpg
It's called chicken run and comes in 12" pieces. You can see the entire piece(s) sitting on top of the heat shrink from Harbor Freight. The crank pulley tool, chicken run, and scotch pads were picked up from other places (the rest Harbor Freight).
http://i121.photobucket.com/albums/o..._3720_rs25.jpg
I think I found the solution to door glue removal:
http://i121.photobucket.com/albums/o..._3721_rs25.jpg
Next up: Karcepts kit cutout and start prepping the interior / engine bay for paint :bump:
Thanks again for all the props and help :cheers:
Yeah, I clicked on this thread. My computer froze, I heard the fan kick on, waited for a while then "must shut down application" popped up. So Im back now, but I had to go strait to page 3 in order to tell you: Good work and keep it up!
Quote:
Originally Posted by TheSnail
Hahaha.... sorry about that :police:
Yeah, there are a ton of pics on page 1, lol. Thanks for the props even though you missed most of the work :yes:
nice stuff keep up the good write up ..
i really enjoyed the long DIY. good luck on the project, cause it takes balls and skill to do something of this magnitude. +1
g/l on the build man awsome work
Nice write up, keep it comming, reminds me of my freind s old eg, gsr swap, with gsr interior and dash. Kinda fun, but we forgot where everything went.
Man good job keep up the good work! :goodjob:
Good luck man.. unlike you.. I just went out and bought a K'ed EG. I don't really have the time to do the swap. If you need anything for you car... I can get it 10% over cost. Since I work at a Honda dealership.
nice nice nice
sick! such good work.
nice build thread.. my buddy is about to start a K20 R swap into his Egg..
goodluck
Impressive, :goodjob:
sick... i love your car. i want one too :(
*subscribes*
this is the first time ive seen meshies on a eg... pretty nice look my friend
that looks clean, wish my car was white.
I was hoping to have the Karcepts shifter kit cut out completed by the end of the day. That didn't happen since I ran into a couple obstacles.
Karcept's shift kit hardware:
http://i121.photobucket.com/albums/o..._3726_rs25.jpg
Make sure the 2 little brackets are correct:
(Note the laptop in the background / it was outside as I worked -- the instructions are about as detailed as you can get :goodjob:
http://i121.photobucket.com/albums/o..._3728_rs25.jpg
Template mounted and 2 holes marked for drilling:
http://i121.photobucket.com/albums/o..._3733_rs25.jpg
Pop's gave this to me as a X-mas gift as well as a few other Harbor Freight goodies. Awesome punch:
http://i121.photobucket.com/albums/o..._3735_rs25.jpg
Drilling the holes:
http://i121.photobucket.com/albums/o..._3736_rs25.jpg
The rear mount bracket was a little wide as you can see in the pic:
http://i121.photobucket.com/albums/o...739_rs23-1.jpg
I marked what needed to be trimmed off:
http://i121.photobucket.com/albums/o...748_rs25-1.jpg
And started trimming with my Harbor Freight polisher/sander (hopefully the neighbors didn't see the camera/tripod when I was taking work in progress pics :screwy:
http://i121.photobucket.com/albums/o..._3752_rs25.jpg
Much better fit:
http://i121.photobucket.com/albums/o..._3753_rs23.jpg
Not sure if I need to trim some off the right side so the left side will sit flush. Karcepts said the gap should pull out fine once the hardware is installed and tightened down. Great service with Karcepts :cheers:
http://i121.photobucket.com/albums/o..._3764_rs25.jpg
Waiting on a router bit to slot the holes. Once slotted I will finish the kit with the cut out.
http://i121.photobucket.com/albums/o..._3771_rs23.jpg
While waiting I have scrubbed most of the engine bay with a toothbrush. I am going to remove the subframe / steering rack for cleaning/paint + better paint job in bay! Then it's time to start prepping for paint :yes:
Thanks again guys for the support :cheers:
bro...this thread is awesome...
mad:reppage:::
I love looking at this thread. Its fucking awesome and so is his work.
Cant wait for more pictures.
Best thread on IA I must say.
incredible work so far! keep us posted.
+1 for you!
Pay me Mcdonald's and Ill help clean the car with a toothbruish.
Should one of the admins sticky this thread... cause the work is almost to perfection....
rediculously meticulous, +1 for jooo mayng
MORE!!!
keep up the good work
I demand more! Awesome work man. What are your intentions for the car? Hard parking or you gonna track it some?
damn dude.. keep it up.. cant wait to see it finished..
Damn that's awesome. How long have you been working on it?
Damn that is a nice ass job! +1
I want to do a wire tuck myself, but i'm still confused what goes where???:thinking: Also, when you do the wire tuck, can you keep everything except powersteering??? I dont want to have to sacrific basic needs, cause its going to be my daily driver...
Keep it comming!:goodjob:
oh dang i was hoping to see more...cant wait to see more...
Work DAMMITT WORK!! Great Job doing it right +1 for you and patience...I break clips and lil shit when I get frustrated...
Funny thing is right now my buddy has a 2nd gen Neon he is doing the EXACT same work too for a SRT4 twin turbo swap..(he's alittle further ahead but has help..sometimes) and the dry ice and removing windows (intact to make templates for lexan) is a bitch. TIP use to people one inside car one out with each holding onto a piece of welding wire and go back and forth the hole way around the windows to remove in one piece to make templates for the light weight lexan :goodjob:
Thanks so much for the props and all the +1's..... and I have not even got into the good stuff yet (motor) haha..... I should be getting a motor within a few weeks. Waiting on the tax return.
Is that TT SRT4 local as well?? I'd like to see it :goodjob:
On to some work from Nov 2006.....
Here is some pics when I removed the sound deadning material back in November 2006:
http://i121.photobucket.com/albums/o..._2345_rs25.jpg
http://i121.photobucket.com/albums/o..._2344_rs25.jpg
http://i121.photobucket.com/albums/o..._2346_rs25.jpg
Is it ok to remove the brown glue or is that a sealer? Should I just clean it up really well, hit it with some sand paper lightly, and paint over it?? (Pic below)
http://i121.photobucket.com/albums/o..._2352_rs25.jpg
Pass side removed:
http://i121.photobucket.com/albums/o..._2355_rs25.jpg
Turned out to be like 9-11 pounds.