project: SNGLCAM

[Axon360]

Not much time, so here's all I can do, for now...

It's just a shell for now, looking to swap an LS1 into it!

First got it about 6 months ago



Now with 16x8's and Stance GR+ coils




I'll post more follow up pics tonight hopefully, been doing a lot to her but also been working tons of hours... thanks for looking!

[b16EG-HaTcH]

MMM thats a sexy stance. i want a 240 now, hurry up and finish it though. Oh and i also noticed you dont have BRB in your sig sir.............

[zyekcim]

paint doesnt match XD no engine looks like its fully gutted... new bumper, new tailights...rims... you need to plug the antenna hole.. scrape all the tint off!.. just playing witcha mayne

[Just_CHill]

WOOT!

[Axon360]

stop rushes meh! haha, and mickey you know too much!

[Axon360]

I have another front bumper now with the lights and grilles! Also got my energy suspension master kit today and ran by summit to buy some POR-15 to coat my frame rails, suspension, and rack and pinion

[Axon360]

removed the rear driver's side lca's and other suspension parts to start swapping my new energy bushings master kit! I took a few more pics to show the progress on the interior and of course, lots more to come. Going to remove one side at a time, swap bushings, install the brand new brake pads and rotors I purchased for the rear so I'll at least have a parking brake. After this, I plan to start my brake line tuck.

[Axon360]

[Just_CHill]

AAAAHHHHHH YEAH!!! Looked good today man!

[Axon360]

started putting por-15 on the driver's side lca, spindle, and hub...came out very nice, didn't even prep the parts much, just a bit of laquer thinner, a paper towel, and some shop air then brush away! Tried removing more bushings in the parts but some of them are in there so tight they won't budge, may have to go by afrotech and pull them on the hydraulic press.

[b16EG-HaTcH]

AFROTECH woooooooo

[Hondatypr636]

Waiting for more pics of your progress

[claybird]

It does look nice

[Just_CHill]

Hurry up with this build man!!!

[Axon360]

Hurry up with this build man!!!

I've been working my ass off lately, I think I'm going to get some more progress next week. Still working on the rear suspension, pressing out these bushings is going to require a press...Keith got one LCA bushing set out, I need to do the rest of them...just don't have time yet. I'm mainly waiting to paint this thing, just bought a paintgun set from BBAT, now I just need to wait for it to warm up \

I also bought a ton of metric tools including 3/4" drive impact sockets up to 38mm if I'm not mistaken, double flaring tool for 1/4" to 1/2" tubing (I think it goes that high), hell...I think I have a better set of tools than Afrotech

[Axon360]

It does look nice

thnx! =p

[Axon360]

UPDATE:::::::::::::::

So I finally found a donor car in my price range, 2000 Camaro Z28. Michael and I pulled the motor in a matter of 2-3 hours, had to come out of the bottom so we pulled the entire forward subframe






Only damage to the engine was the power steering pulley and reservoir was destroyed, the driver's side valve cover was damaged. Valve cover has been taken off, no internal damage.

[OldsTech]

Looks good bro!!!...but looks better in person .....and funner

[Just_CHill]

Dude, where are all the other pictures?!?!

[Relentless]

niice build you have in progress, cant wait to see the outcome!

[Axon360]

well the fbody oil pan has been traded for a gto pan that will be on its way later this week. Replacement valve covers and gaskets are in!!! Also got rear brake caliper rebuild kits and I will be taking pics as I work on it soon. DAFT INNOVATIONS LS1 mount kit is here as well, more to come..!