I smell Fraud!!!!

[Mr.MuayThai]

10 seconds all motor. . . b16. . . check it out!

http://atlanta.craigslist.org/pts/399568262.html

[will_2006]

hmmmmm.... maybe he meant 1/8

[Mr.MuayThai]

^^ doubtful. He probably just bought a b16 swap for like 1500 bucks and is trying to sell it for 2500 and tell everyone that there is type r internals. . . wouldn't you have to bore it out to get the pistons in there? I might look into this, and run with it.

[speedminded]

Just about anything is possible but i'd say very unlikely, i've seen an all motor SOHC in a gutted and caged CRX run high 12's to 13 flat on slicks...but it was a built motor with gearing specific for the 1/4. I'd say it would have to be 1,200lbs or less to make it near the 10's.


B16A PR3:
ROD LENGTH: 5.290”
STROKE: 3.031”
BORE SIZE: 3.189 “(81MM)
COMPRESSION HEIGHTS: 1.180”
DOME HEIGHT: .098”
WEIGHT: 299 GRAMS

B18C5 P73-A0
ROD LENGTH: 5.429”
STROKE: 3.433”
BORE SIZE: 3.189” (81MM)
COMPRESSION HEIGHTS: 1.190”
DOME HEIGHT: .070”
WEIGHT: 310 GRAMS


B16 with a USDM ITR piston (P73-A0) is only going to be 10.4:1 compression and using the JDM ITR (P73-00) would make it 10.7:1. With a B16 i would have put in the CTR (PCT) piston and had 11.1:1

[RandomGuy]

pshhh forget that


i got 7.8:1 on my car lolol (really)

[highspeed]

pshhh forget that


i got 7.8:1 on my car lolol (really)

hahahahahah

[ash7]

...Last fall Rocket Motorsports put a NA b18 crx downrange for a time of 9.3 in the 1/4 mile. Breaking Skunk2s claim to fame with their NA RSX. (boohoo)

i think it's totally possible... although i havn't looked at the link you supplied though...

I'm on dialup right now....*sigh*[looks down at shoes while waiting for page to load]

(good stuff there btw speedminded)
-jonathan

[xlilvi3tx]

it possible dude. but i dont think that type of set up would hit 10s. to hit 10s in a n/a takes lots of money n u gotta build more than that.

[AnthonyF]

speedminded-your knowledge of everything hurts me head.

[AnthonyF]

it possible dude. but i dont think that type of set up would hit 10s. to hit 10s in a n/a takes lots of money n u gotta build more than that.

wait.....WHAT? it's possible but not this setup?ur confusing.


It is possible to hit 9's NA too....ON A BIKE!!!!!!

[n1accord]

pshhh forget that


i got 7.8:1 on my car lolol (really)

BOOST IT! .....that is if it isn't already!

[DUBSf22c]

It is possible to hit 9's NA too....ON A BIKE!!!!!!

now ricer. it is skunk and rocketmotorsports (db1 says) did it nicely

[ash7]

speedminded-your knowledge of everything hurts me head.

Speedminded has an IQ of 210 to the seventh power

-jonathan

[allmotoronly]

maybe if he had that engine in a bare crx chassis with no interior except the steering wheel and an egg crate to sit on.

[AnthonyF]

now ricer. it is skunk and rocketmotorsports (db1 says) did it nicely

umm....what?

[OMG Its Platz]

...
I'm on dialup right now....*sigh*[looks down at shoes while waiting for page to load]


-jonathan

[man]

pshhh forget that


i got 7.8:1 on my car lolol (really)

8.5 for meeeeeeeeeeeeeeeeeeeeeeeeeeeee

[RISKYB]

agreed i call bullshit as well

[an0therh22]

this setup would not run 10s in a crx. all he has is just the R pistons and intake manifold. i dont think this setup even yields the C5 stock power. Oh maybe hes running 10s because he has HEADERS! 2>1 FTW

[JDM onlyy]

^^ doubtful. He probably just bought a b16 swap for like 1500 bucks and is trying to sell it for 2500 and tell everyone that there is type r internals. . . wouldn't you have to bore it out to get the pistons in there? I might look into this, and run with it.

No, the pistons and rods will work. What makes the b16 a 1.6 liter is the stroke, and the same goes for the b18.

[Jecht]

BOOST IT! .....that is if it isn't already!

Its a Starion/Conquest... it is most certainly already boosted.