There is a Buick race going on but I'm planning on going to TNT. Who wants to come with me??
SDR Saturday 11/7
There is a Buick race going on but I'm planning on going to TNT. Who wants to come with me??
Why not come out to the Friday night TNT on the 6th?
'92 C2500 6.5 Turbo Diesel | '96 240sx
I got some work to do on the car on Friday. I'm getting off early today so maybe I can squeeze some of it in...I have to leave Atlanta area around 2:30pm on a Friday to beat the traffic, or else its a no go...
There will be a few people there on Friday night. I know the Evil Goat will be there as well as myself and Catnip put a thread I believe in the events forum.
JJSPEC RACING - Central Ga's source for performance parts,fabrication, tuning, general repair and a whole lot more! 478 621 5000
I will be there Saturday doing more testing.
98 Trans Am, 427LSX,94mm Turbo
Thanks to Josh@ Kentucky Turbo for the Turbo Setup
I like your sig Hunter xxxxrwhp xxxxrwtq. You make me jealous, lol!
JJSPEC RACING - Central Ga's source for performance parts,fabrication, tuning, general repair and a whole lot more! 478 621 5000
Originally Posted by jjmastertech
Maybe you should get a man's car?
I kid.
BTW, does jjspec have any 3" mandrel bent piping? Aluminum or steel, doesn't matter, just need a 60 degree bend for my intake.
'92 C2500 6.5 Turbo Diesel | '96 240sx
Yeah, I know. Just working with what I have laying around the shop. If I ever get a rwd chassis, I have a 350 fully machined waiting for me to put it together and installed. I will have to look. I believe I have a 180* 3 in al bend. If that will work let me know. You can cut it to your specs and I can weld it for you if you would like.Maybe you should get a man's car?
I kid.
BTW, does jjspec have any 3" mandrel bent piping? Aluminum or steel, doesn't matter, just need a 60 degree bend for my intake.
JJSPEC RACING - Central Ga's source for performance parts,fabrication, tuning, general repair and a whole lot more! 478 621 5000
Oh, I was just messing with you man. Nothing at all wrong with what you're doing.
Any idea how much it'd be to do this:
(all measurements are just rough guesses)
8" section to the 60 degree bend, then about a 12" section... PM me if you'd like.
'92 C2500 6.5 Turbo Diesel | '96 240sx
I know you are just messing with me, lol! PM me in the morning and I may actually be able to get something perfect for you. Is it def 60*?
JJSPEC RACING - Central Ga's source for performance parts,fabrication, tuning, general repair and a whole lot more! 478 621 5000
I'll double check all my measurements (and on LS1tech) tomorrow and let you know. Thanks man!
'92 C2500 6.5 Turbo Diesel | '96 240sx
Aaron I MIGHT be able to go......ill let you know....Saturday would be good
slower than you
I might come out saturday, thats if my 10 bolt isnt broken again by then.
1998 Camaro Z28 headers/clutch/shifter/full suspension 12.6@122 awaiting install prc dual valve springs, fms pushrods, custom grind fms camshaft: 234/238 .601/.612 114lsa
1997 Buick Regal GS - stock 14.8@94
I might roll up from southern
Just a riced out F-150
MSS MAFIA
Sounds good Jerry, I know Hunter said he is having tranny problems so he is doubtful. I will see what happened with his car today...
Cool man! Make the trip!
I am out for saturday. A $2 snap ring broke inside my tranny, so I will be out till next week.
98 Trans Am, 427LSX,94mm Turbo
Thanks to Josh@ Kentucky Turbo for the Turbo Setup
I need to change the sig. I guess I can do that now. LOL!
98 Trans Am, 427LSX,94mm Turbo
Thanks to Josh@ Kentucky Turbo for the Turbo Setup
Im out...I wanted to go if Hunter was and finally see him run some preliminary numbers..that 9.6x he ran was a chump run for that car.....he will be in the 8s easy very soon as long as the 17" Drs hook. Otherwise he will run low 9s at some stupid mph.
slower than you
Posting Permissions
Reply With Quote
