I fail to see the "Ballin' outta control, hasn't been washed in 6 months" option.
I fail to see the "Ballin' outta control, hasn't been washed in 6 months" option.
my car is sitting in my garage waiting for me to buy the few last parts i need and finish it up. It also has a b18c1 and you guys don't want any. lol jk.
Broken, being parted out, building new car
well fuck, the wrong part shipped to me today. so now i have to wait for the right one to be shipped
Still waiting for the software so I can run Alpha-N (i.e no maf) for my carbon intake manifold/intake. Should be epic
mine is ready to rock and roll. MCE day on the 21st at sdr will rock!
slower than you
I plan on going to MCE day to watch and maybe make a few fun runs. Cant wait to see some nice muscle cars.
JJSPEC RACING - Central Ga's source for performance parts,fabrication, tuning, general repair and a whole lot more! 478 621 5000
I voted 4 times.
just sayin.![]()
WHERE IS THE WAITING ON MONEY OPTION? I'M TRYING TO GET THESE SIDE SKIRTS FROM THIS GUY. BESIDES THAT I NEED NEW REAR CALIPERS AND WANT TO DO THE FRONT BRAKE UPGRADE W/ SS BRAKE LINES ALL THE WAY AROUND W/ THE FRONT STILLEN LIP AND STAGGERED WHEELS...THEN WORK ON GETTING THE SOUNDS RIGHT ON THE INSIDE...I'M FAR FROM DONE AND FAR FROM 'WAITING ON PARTS'
Waiting on my 3 fuel filters to arrive today so I can re-assemble my fuel system.
98 Trans Am, 427LSX,94mm Turbo
Thanks to Josh@ Kentucky Turbo for the Turbo Setup
Mine are asleep in the garage.
Mustang got new wheels this week and I couldn't have the Lightning getting jealous so it got something too!
Here for fun!
Clapped out Mustang checking in!!!!!!!!
gathering parts for the swap. almost ready to start but i know it will take longer than expected.
I need balancer, water pump, thermostat, belt tensioner, alternator, alternator bracket, idler pulley, power steering pump, power steering reservoir, power steering pulley, power steering hoses, all kinds of bolts, starter, flexplate, pilot spacer, electric fuel pump, fuel pressure regulator, radiator hoses, quarterpanel, and who knows what little odds and ends will come up in the meantime. Lots'o'shit.
how about spun a rod bearing and is in the garage in a million parts
Originally Posted by quickdodge®
Originally Posted by Stretch®
Originally Posted by AllStock
waiting on tons of parts for the mini.... new switch box, new compressor, new valves, new paint (this spring), new rims, a tune, and a turbo lol.... its probably gonna be a minute on this one.... :-(
Drillin' switches on them bitches!
Ridin' So Low...
Mine was working for about 15min then cam locked up and bent exhaust valves so now i have to send the camshaft off to get repaired and buy a few other things to get it back running again. What a yr
Soon!!
I have a 70,xxx mile gs-r sedan in perfect shape that has taken over 10k from my wallet, yet always needs just ONE MORE PART to be finished, FML!
2008 Scion xD (38mpg ftw!)
2005 Chevy 1500(For towing)
1991 5.0 lx(45,xxx original miles)
2000 DB8 GS-R ( Built and SOLD)
2001 Crown Vic(61,xxx original miles)
1997 Honda Accord Ex(sold)
1995 Nissan 240sx/se(Sold)
1995 Toyota Tercel(4EFTE Swapped)(Sold)
1991 VR4 1102/2000(Sold)
Parts are waiting to be installed and then I am ready to race once I get some drag radials or slicks.
Got to finish my wife's car, then the resurection will begin...
JJSPEC RACING - Central Ga's source for performance parts,fabrication, tuning, general repair and a whole lot more! 478 621 5000
JACKSTANDS......All through my garage
Here for fun!
Clapped out Mustang checking in!!!!!!!!
Last edited by QKJUICEDPONY; 12-23-2009 at 08:42 AM.
Here for fun!
Clapped out Mustang checking in!!!!!!!!
Work in progress! Got to order some parts.