PDA

View Full Version : Power Mods Freakin stupid turbos



PSINXS
03-14-2007, 07:27 PM
Any tips on how to seperate the exhaust housing from the center section? i know its supposed to rotate but mine seems rusted on. Any ideas tobreak it loose? i tried hammer, wd-40, deep creep, and nothings happening. i need my freakin car to run!!!

Benefit
03-14-2007, 08:37 PM
are you trying to clock it

Big J
03-14-2007, 11:18 PM
torch son, add a little heat

§treet_§peed
03-14-2007, 11:21 PM
hair dryer? and a flat head screw driver and maybe a 5 lb hammer to help conveince it?

miro_gt
03-15-2007, 12:55 AM
get a damn McDonalds burger, and try again

Big J
03-15-2007, 07:01 AM
if it's a factory turbo it might have a pin to keep it from being clocked, which means you'll have to pull the housing off and remove the pin (just fyi if it's an oem turbo)

Benefit
03-15-2007, 04:58 PM
i would make sure u have all the bolts off first

PSINXS
03-15-2007, 07:17 PM
compressor housing is off. all bolts out of the exhaust housing except two that the center section wont let move all the way out. i am gonna torch it up and see if i can get this sucker to turn.

turbosx©
03-15-2007, 08:22 PM
buy a new turbo?

Krazykouki
03-15-2007, 09:17 PM
thats what I keep telling him. Get a new turbo. Hitting it with a hammer like some of you are suggesting is just plain stupid, have any of you ever worked on a turbo before?? His housings are cast iron and they will crack.

I suggested heat, I will torch it up tomorrow for you, just remind me.

Oh and if I get it off you owe me lunch, I will do it during lunch.

turbosx©
03-15-2007, 10:14 PM
if anything B. jus buy a cheap one off ebay for a temp setup.even if its an SS one

Krazykouki
03-15-2007, 11:08 PM
if anything B. jus buy a cheap one off ebay for a temp setup.even if its an SS one

Bad idea. If it blows it can tear apart his freshly built motor.

§treet_§peed
03-15-2007, 11:45 PM
thats what I keep telling him. Get a new turbo. Hitting it with a hammer like some of you are suggesting is just plain stupid, have any of you ever worked on a turbo before?? His housings are cast iron and they will crack.

I suggested heat, I will torch it up tomorrow for you, just remind me.

Oh and if I get it off you owe me lunch, I will do it during lunch. i'm not sure if you can tell but i was being sarcastic

2.3 Evo 8
03-16-2007, 01:54 AM
1. Get a room at the Marriot hotel on the top floor.
2. Open window.
3. Drop turbo out window.
4. If it doesn't work, repeat step 3.

Krazykouki
03-16-2007, 09:26 AM
i'm not sure if you can tell but i was being sarcastic

I know. Its the other dumbass's who will actually try that and break their shit.

Kevykev
03-16-2007, 09:31 AM
^ hahaaa!


Damn Bradon, I almost wanna give you mine to drive*, you've been through it all.




*no, not really

turbosx©
03-18-2007, 04:56 PM
Bad idea. If it blows it can tear apart his freshly built motor.


i didnt mean for a permanet fix jus temp until so he can drive the car.unless he still gots to break in da motor.if thats the case check kat.org