My 3 Rotor Project..

[Herblenny]

I've posted this on other forums so pardon me if you already saw this somewhere else.. However, I'll shorten things and post just pics of what's been happening since Nov. last year.




To start.. the car.. I found a guy selling a 93 VR touring FD in New Orleans. Luckily it was just a shell but didn't have a title. Seller said, it had a clean title but does not have it because the guy he bought it from never sent it. Luckily through my rotary car connections, I was able to contact the previous seller, and then the seller before that to get a clean viable title.


Here are some pics of the car when I was picking it up from New Orleans.










Next morning in New Orleans



From there car went to my friend and fabricator Walker Morgan @ Morgan Performance Fabrication





At MPFab, we installed the engine in so walker can develop a new manifold for the car.


The 20B/ 3 Rotor Engine...


Here is when it was just built.














Its from the last year Eunos Cosmo 3 Rotor, "D" series motor, broken down and rebuilt with ported intake, less restrictive 13B-REW exhaust sleeves, Balanced rotating assemblies, Lapped housings, and all new seals and gaskets... And built by one of the best builder I know.. Luis Canizales.








Engine in!

[Herblenny]

I was initially going to use my previous 3 rotor manifold I had but my friend Walker Morgan convinced me to do something different...

Old manifold







And went with 321 SS (which wasn't cheap) and went with something different... here are some pics of Walker's art work (Morgan Performance Fabrication)





A brushed 321... equal length, bottom mount turbo (first I've seen on a 3 rotor).

One of the issues later we found was that the motor mounting kit I purchased wasn't made that well and the engine did not sit flat. It took us a half day with 3 guys trying to make things sit flat before moving farther along..

[Herblenny]

Because I was using a stainless goodies, I had to get the flange cut perfectly flat before all the tubings got welded by Walker @ MPFab.



If flange is not flat and tubings are not welded correctly, the heat this engine will produce will warp the flange and will have a leak.

Here are some pics of the DP, turbo flange, heat shields, etc that MPFab.com made. The welding skill is one of the best in the country!!

[Herblenny]

Downpipe is so straight, you could see the other side!





Now the set up on the engine.. with the turbo..







And the rare Titanium catback from Japan..

[Herblenny]

More pics of the turbo/manifold set up..

[Herblenny]

We decided to go with Bell Intercooler cores for our cooling needs. Bell Intercooler guys have been awesome to work with and shipped the parts ASAP to us.
Walker have used their product in many of his high horse power cars he had build in the past and that was good enough for me to buy Bell products.



Mocking up the V-mount set up on the 20B project..

[dragoncelica]

Nice Job!

[WhiteAccord]

Nice Build....

[NoWAyItZTOMmY]

nice!!

[RandomGuy]

Quality work. This will be an achievement once you're done!

Simply sick

[Herblenny]

Thanks for the kind words!

[Herblenny]

While MPfab was working on the other cars in the shop, I've decided to clean up the engine bay for cleaner look by removing the seam glue.







progress on the V mount





air channel plate made..








How it looks without the cardboard and radiator hose fab'd

[Herblenny]

More pics...



Now test fitting the bumper and such..





Test fitting the RE-Amemiya carbon fender mirrors



My friend at ShineAuto made this fender specific for me with carbon bottom half.

[Kyle]

holy shit.

[Herblenny]

Thanks to Tial USA, I got a matching wastegate (water cooled) and BOV.

Here are updated engine pics.




Test fitting the Widefoot sway bar mounts that I got like 5 years ago.. and Tripoint sway bar.... making sure its not interfering with anything we custom made.



Side panels made by Walker Morgan from MPFab.com



More trimming and such to the bumper... This bumper is different from the one posted earlier as my previous paint and body messed it up.



I now have a new paint and body guy.. Jonathan Goolsby from Goolsby Customs - Custom cars and collision
Goolsby won last year's SEMA GM Design award.

[Herblenny]

At this point, pretty much all of it has been done at Walker Morgan's place (Morgan Performance Fabrication = Morgan Performance Fabrication).

Here are couple of images before the car was once again put back to a shell to be moved to paint and body.



How it will look from viewing from front.


couple of days of cutting the bumpers.


new black wastegate from TIAL



Pulled fabricated goodies..


Now pulling the motor out and other stuff..

[Herblenny]

Picked up the car from MPFab.com and transfer to Goolsby Customs (Goolsby Customs - Custom cars and collision).



How it sat the first day..

[Herblenny]

During this build, I had a chance to go visit Chris Ludwig from Ludwig Motorsport to check on the harness for the engine.

We decided to use the AEM coils with the Haltech PS2K.



Mil-spec connector..

[Herblenny]

next few days, I brought all my exterior parts from my home to Goolsby's..

Here are some pics of the CF goodies..



A rare FEED GT II R wing that I drove to VA to pick up.



After few days at the Goolsby Customs.. car starting to look like what it will look like

[slow_hatch]

I love build threads and this looks like it'll be a good one.

[Sinfix_15]

i wasnt prepared for the level of awesome i was going to experience when i clicked this thread. Hats off to you sir...........

[TIGERJC]

Nice build. Do you still have the other 2 RX7, if so can you post some updated pics of them

[green91]

WOW. Im extremely impressed, the fab work is absolutely top notch and an awesome set up. Mucho kudos to you!

[MeFryRice]

This is an awesome build.

[NAIZBST]

awesome build and fab work!!!

[Herblenny]

I love build threads and this looks like it'll be a good one.

I hope it will meet your expectations..

i wasnt prepared for the level of awesome i was going to experience when i clicked this thread. Hats off to you sir...........

Thank you!

Nice build. Do you still have the other 2 RX7, if so can you post some updated pics of them

I do
Here are couple of latest pics..


simpler look since I'm going to street this car more.. and the wheels are just to test out (which will go on this project).


SSM is still the same.. except with this CF license plate that I made.

WOW. Im extremely impressed, the fab work is absolutely top notch and an awesome set up. Mucho kudos to you!

Thank you! Walker Morgan from MPFab.com did an amazing job! The guy is an artist!!

This is an awesome build.

THank you!

awesome build and fab work!!!

Thank yoU!

[Herblenny]

While the car was at Goolsby Customs, I've decided to start making the engine pretty





Short block done

[Herblenny]

Again, while I was waiting.. I started to work on the engine..

Thanks to my oldest sponsor Exedy Clutch, they sent me their lighten twin disc clutch!
Exedy USA has been the best company I have ever worked with and I really appreciate their constant support!! Thanks Exedy!! EXEDY Globalparts Corporation

If you don't know about Exedy Clutch, they are OE manufacture for almost all Japanese cars. They also produce many great racing clutches. Quality and their quality control is far superior than any other companies out there.

Anyhow.. pics..

[Herblenny]

More parts were put on my Goolsby Customs and being test fitted and gaps are adjusted..









Been collecting these body parts for some time...

[Scotsman]

WOW is about all i can say , simply amazing work!

[Herblenny]

WOW is about all i can say , simply amazing work!

Thank you!

[Herblenny]

Again, while I was waiting on the shell..

decided to shave off the casting seams and paint the Upper intake manifold of the engine.



I was going to powder coat it red.. but thought i give the similar gray black look





and inserted a carbon fiber to tie the whole car together

[Catnip]

The whole build(s) look awesome. Digging the intake manifold, as well.

[dragoncelica]

$$$$$$$$$$$$$$$$$$$$$$$$$$

[stealth1]

Good stuff!!! I can see a possible magazine cover shoot in the making …….hell this could be the center fold for playboy and I would not miss a beat!

[Herblenny]

The whole build(s) look awesome. Digging the intake manifold, as well.

Thank you!

Good stuff!!! I can see a possible magazine cover shoot in the making …….hell this could be the center fold for playboy and I would not miss a beat!

LOL! I appreciate the kind words

[Herblenny]

While I was doing all that, Goolsby Custom was busy doing these things..





Cut the rear flare.


Installed both my FEED wing and the tail light lip cf spoiler.

[silverZ33]

Simply unbelievable time and care put into every detail...cannot wait to see the finished product

[Boosted FC]

The amount of attention to detail that is going into this car is unbelievable. Phil has never taken shortcuts on any of his cars, and this build just reinforces that. Cannot wait to see this one finished good sir.

[Herblenny]

Simply unbelievable time and care put into every detail...cannot wait to see the finished product

Thank you!

The amount of attention to detail that is going into this car is unbelievable. Phil has never taken shortcuts on any of his cars, and this build just reinforces that. Cannot wait to see this one finished good sir.

Ahh.. I really appreciate that!! I hope this build doesn't disappoint you.. You coming to DGRR next year?? Hope this car will make it.