head gasket problem

[TokienMan]

I got a Toyota Pickup with a bad head gasket trying to find someone to do the repair cheap. I dont have any extra time with school to do it myself. Anyone know someone who can do the repair let me know?

[Tech5]

Cheap lmao, everyone wants cheap...just remember you pay cheap you get cheap service = more problems, go ahead an get it done right the first time, athen no head achs later

I got a Toyota Pickup with a bad head gasket trying to find someone to do the repair cheap. I dont have any extra time with school to do it myself. Anyone know someone who can do the repair let me know?

[EJ6]

Cheap lmao, everyone wants cheap...just remember you pay cheap you get cheap service = more problems, go ahead an get it done right the first time, athen no head achs later

speaks the truth

---EDIT----

unless u trust the motherf*cker....some folks do it for a good deal..so dont let those deal pass u if u know that person etc

[TokienMan]

haha. I mean any one know someone who does good work??

[Tech5]

then your gonna pay for it too......lol.....your looking around 1,000 for that one, with getting the head to the machine shop so they can deck it an check it........then depending anything else had to be done. then your headset an labor an all....an if you have alott of miles, then I really think you should go with another engine, used one, with less miles, if yours have (example) 200k miles, an you have a bad headgasket, depending how hot it go, which you cant tell , unless you take your head to the machine shop you might warped the head, so when you have that issue fix, an they shave it ,then put on your stock 200k mile motor, sometimes it will throw your bottom end out, an cause it to start knocking, just my 0.02 cents

[b18cEG]

what year and what size motor. 2.7 or the 3.4. my experience the 2.7 always the head problem and if u have the 3.4 rare too have it.

[b18cEG]

i stay in stone mountain.lmk

[SleeperWRX]

Pay cheap and get more problem usually shop would charge you around $500-$800 and thats if you get a new gasket. That worst part of all that is Timing

[Sammich]

that should only run you $300-$500 at the most to get it done right. i just got mine replaced...its not that bad of a job to do

[SleeperWRX]

that should only run you $300-$500 at the most to get it done right. i just got mine replaced...its not that bad of a job to do

Can you share with the ^^


lol

[Sammich]

what u mean? i'm pretty sure it's a worse job if you are carb'd like i am because of all the vacuum hoses you have to remove...but generally..on a 22r, its a simple job, remove the hood and its pretty self explanatory...or get a chilton/helms manual

[SleeperWRX]

remove the hood

[Sammich]

our hood doesnt tilt back as far as integra hoods...its easier to work on the truck with the hood removed

[Blitanicle99]

Well for one, thats my buddy and its a 3.0... And Michael call me tomorrow and Ill give you Chris's number I met him through Matt Hardy, the guy was a Toyota mechanic for 30 something years and does good work for cheap. And his shop is right off easy piedmont by allgood.

And 22rs are easy gasket job. I am looking to do a 22r hybrid with a 20r head. Apparently they make like 157 hp on a carb'd motor.

[Sammich]

Well for one, thats my buddy and its a 3.0... And Michael call me tomorrow and Ill give you Chris's number I met him through Matt Hardy, the guy was a Toyota mechanic for 30 something years and does good work for cheap. And his shop is right off easy piedmont by allgood.

And 22rs are easy gasket job. I am looking to do a 22r hybrid with a 20r head. Apparently they make like 157 hp on a carb'd motor.

my fault...i assumed it was a 3.0...g/l on that lol. and thanks for the confirmation of the simplicity of the 22r head job..

if i can find a 22re-t to drop in my piece...

[Blitanicle99]

They are all over craigslist all the or do what I am doing...

[integraguy06]

remember mike, the big D knows someone