TDC B16A

[88EF_tHiS]

MY ENGINE IS THROWING THE 8CODE....WHICH MEANS TDC SENSOR.....I FIXED THE TIMING......I JUST CANT FIGURE OUT WHY THE DAMN LIGHT IS STILL ON......WELL, CAN SOMEONE HELP ME OUT...BY TELLING ME WHERE THE TDC SENSOR IS LOCATED.....IT MAY BE BAD....BECAUSE THE LIGHT COMES ON ONLY WHEN THE CAR IS AT ITS RIGHT TEMPERATURE.....OR AFTER DRIVING FOR COUPLE MILES....oh N ONE OTHER THING.....I NEED EMISSIONS also....does anyone do hot emissions for less than 100??? thnaks

[BABY J]

distributor

[88EF_tHiS]

where in the distributor????? on top??? oh and do you know if a 88crx with a b16A swap will pass emissions w/o a cat converter? i believe its obd0

[SLow_POke]

x2

distributor

and the dizzy is located byt hte thingamageta next to the whachamabob

[88EF_tHiS]

lol wth???

[BABY J]

YOU fixed the timing - but you do not know where a distributor is. FURTHERMORE you want a shop who PAYS for state certification to do emissions to openly post that they do under the table emissions...

[88EF_tHiS]

ummmm i said where in the disrtibutor????? can u read???? is the sensor the whole damn disrtibutor???? or is it a piece of it?????

[88EF_tHiS]

oh n some people do it....theres a little icon called private message!!!!!! people do pm about emissions.......ive received several

[BABY J]

Back on topic -

1) disconnect neg batter terminal for 5 mins.

2) while u are waiting, disconnect the ECU totally from the car.

3) afterwards, inspect the dizzy plug for any disconnected or burned through wiring. The wires should be soft and pliable (bendable). OBD0 swaps have been on the road so long that the dizzy wires (due to heat) could be getting hard/brittle and less conductive to electricity. Re-solder and re-pin any/all wires that have gotten hard.

4) inspect harness plugs that plug into the ECU. Make sure that none of the wires have fallen out of the pins.

5) connect ecu back to the harness, ensuring that you feel/hear the "click" from the tab

6) turn the key to "run" position (until the fuel pump primes) and then start. After warm-upm see if the car will rev over 4k rpms.. if so, FIXED.

[88EF_tHiS]

damn.....thanks dude......thats exactly what my car is doing....it wont rev over 4.....thanks imma do what u say n ill get back to ya...i appreciate this

[88EF_tHiS]

does anyone know about obd0 cars passing emissions w/o a cat converter

[BABY J]

damn.....thanks dude......thats exactly what my car is doing....it wont rev over 4.....thanks imma do what u say n ill get back to ya...i appreciate this

I knew that. I am a genius. Also make sure you have a recent oil change. Believe it or not, when your oil is toasted the obd0 ECU will not let the car rev over 4k as well.

[88EF_tHiS]

i dont think its the oil....cus it had an oil change bou t 300 miles ago....unless something terrible caused the oil to burn up....but ill check that also.....but do u know about the cat?

[BABY J]

Not sure on emissions - I've always had the hookup.

[88EF_tHiS]

well, can u hook me up with ur hookup lol ? if at all possible?

[BABY J]

I will see what I can do - I have lived in Indianapolis since August 06 - (no emissions here) so I gotta see if he is still in the business.

http://www.angelfire.com:80/ca/DrOhm...torRepair.html

[88EF_tHiS]

aite koo

[GSRteg®]

LOL

where in the distributor????? on top??? oh and do you know if a 88crx with a b16A swap will pass emissions w/o a cat converter? i believe its obd0