Results 1 to 10 of 10

Thread: Pro Cars Can't Be Club Raced....

  1. #1
    Senior Member | IA Veteran Elbow's Avatar
    Join Date
    Mar 2005
    Location
    Atlanta
    Posts
    29,397
    Rep Power
    65

    Default Pro Cars Can't Be Club Raced....

    This has been on my mind for a while now as I've been looking at cages and what not for my BMW for next season.

    A friend was recently told he can't run HPDE because he has a ERW tubed cage and NASA requires DOM in race cars, rules say for HPDE if you have a cage or bar it must meet their CCR requirements for race cars... Kind of stupid if you ask me. They never check anyway.

    So then I got to looking at race cars from say BTCC or something and found many saying they aren't legal safety wise to run NASA or SCCA... Really? I'm PRETTY SURE there HAS to be a way to bring in a FIA touring car or something.

    This:



    Isn't as safe as this?



    I'm pretty sure I'd rather be in the first car then a car with a 6 point bolt in cage.

    I know I know it's insurance purposes. So does anyone know for sure if an FIA legal car can be brought into SCCA or NASA? The HPDE rule thing is just flat out stupid if you ask me, they won't check anyway, not that I'd trust registering hoping that but in my experience they won't check cages or bars in HPDE.

    End rant lol.

  2. #2
    f-ckouttahere. PROŽ's Avatar
    Join Date
    Jul 2007
    Location
    hanging around here(hair) like some earrings
    Posts
    2,635
    Rep Power
    22

    Default

    saw this thread, and initially wasnt going to reply, being that i know nothing of this topic, UNTIL i saw the title.

    for the record, these are NOT my cars.

  3. #3
    Share the road SLOWR/T's Avatar
    Join Date
    Mar 2005
    Location
    G-net
    Posts
    4,344
    Rep Power
    25

    Default

    Quote Originally Posted by PROŽ View Post
    saw this thread, and initially wasnt going to reply, being that i know nothing of this topic, UNTIL i saw the title.

    for the record, these are NOT my cars.
    At first I was WTF did he reply for.... then I got it
    One Big Ass Mistake America

  4. #4
    Senior Member | IA Veteran Elbow's Avatar
    Join Date
    Mar 2005
    Location
    Atlanta
    Posts
    29,397
    Rep Power
    65

    Default

    Haha X2..smooth!

  5. #5
    www.jasontbarker.com speedminded's Avatar
    Join Date
    Nov 2003
    Posts
    22,589
    Rep Power
    52

    Default

    1. Where does it mention no "pro" cars?
    http://www.nasaproracing.com/rules/ccr.pdf

    Requirements

    • Membership in NASA or a NASA sanctioned club
    Any car in safe operating condition (from Ferrari to • Hyundai)
    • Mufflers. Different tracks have different sound policies
    • Roll bars in convertible autos
    • Seat belts in good working order
    • State driver's license
    • Long sleeve shirt and pants (cotton is great)
    • A helmet
    • Knowledge of the Club Codes and Regulations
    • At least 18 years of age (16 w/parental consent)



    2. Only convertibles are required to have roll bars in HPDE right?!

    11.4.7 Roll Bars
    All open cars should have a roll bar installed to help protect the occupant(s) from injury
    during a roll-over. The roll bar should be able to withstand the compressional forces
    involved in supporting the full weight of the car. The roll bar’s main hoop should extend
    the full width of the car (except certain cars that have been approved by NASA). The
    main hoop shall be one continuous piece with smooth bends and no evidence of
    crimping or wall failure shall be present (i.e. should be Mandrel bends). All welds should
    be of the highest possible quality, with full penetration [Ref: (15.6.15)]. All cars with roll
    bars are required to have adequate roll bar padding per CCR section #15.6.4. In cases
    where the driver’s head may come in contact with the roll bar should the seatback fail, a
    seatback brace is required in conformance with section #15.6.22. The material and
    minimums are as follows: (All cars with full roll cages should conform to the applicable
    sections found in section #15.0.)

    Vehicle weight DOM or ERW
    Under 2000 lbs. 1.50" x .120”
    2001 - 3500 lbs. 1.75" x .120"
    Over 3500 lbs. 2.00" x .120"




    15.6 Roll Cage
    (See diagram at end of section)

    15.6.1 Purpose
    The basic purpose of the roll cage is to protect the occupant in case of a rollover or a
    collision. It should be able to withstand the weight of the car landing on the roof. These
    rules apply to all classes, unless otherwise superseded by the class rules. Vehicles
    homologated by, or built to the specifications of, SCCA, IMSA, and Grand AM must
    conform to these rules, or may conform to their respective current class rules for roll
    cage requirements for guest groups and special events. Any vehicle that does not
    conform to the NASA cage rules, yet conforms to cage rules of another recognized
    sanctioning body (SCCA, IMSA, Grand Am, etc.), that wishes compete in NASA events
    on a regular basis, should be ordered to make modifications within a time frame
    specified by the Race Director and approved by the Regional Director. Note- It is the
    responsibility of the driver to furnish a copy of any non-NASA rules applicable to his/her
    vehicle.

    15.6.2 Intent
    Chassis stiffening is a side benefit of a good roll cage system, but it is not the intent of
    these rules. Parts of the cage deemed by the Chief Scrutineer, to serve no practical
    purpose other than chassis stiffening may be considered in violation of the intent of
    these rules (Note: Some class rules allow for chassis stiffening.). The Chief Scrutineer
    may order the removal of said parts, or require that the vehicle owner redesign,
    reconstruct, and re-certify the roll cage if warranted. The removal or redesign of the
    cage, whole or in part, to comply with these rules, does not imply that penalties will not
    be issued for violating the intent of these rules.

    15.6.3 Installation
    The cage may be removable or may be permanently welded, or any combination
    thereof, providing that all aspects of the cage meet these rules.

    15.6.4 Padding
    All roll cage surfaces that may come in contact with the driver should be padded with
    high-density padding such as Ethafoam or Ensolite. It is recommended that padding
    meeting SFI specification 45.1 be used.

    15.6.5 Bends
    None of the tubing may show any signs of crimping or wall failure. All bends must be
    Mandrel type. The center radius of the bends may not be less than three (3) times the
    outside diameter of the roll cage tubing.

    15.6.6 Main Hoop
    The main roll cage hoop should be as wide as the full width of the interior and must be
    as close to the roof as possible without violating CCR section #15.6.20 Inspection. One
    continuous length of roll bar tubing shall be used as the main hoop. The main hoop
    must consist of not more than four (4) bends maximum, totaling one hundred eighty
    (180) degrees +/- ten (10) degrees.

    15.6.7 Diagonal Brace
    One (1) diagonal brace shall be used in the same plane as the main hoop. The
    diagonal should be one continuous path; meaning that it must conform to Diagrams
    15.6.7a or 15.6.7b. Note- If the installation method from Diagram 15.6.7b is used, the
    builder should pay close attention to alignment. One end of the diagonal brace shall
    attach to the corner, or horizontal part, of the main hoop above the driver’s head, within
    twelve (12) inches of the driver’s-side corner. The other end of the diagonal brace shall
    attach to the mounting plate (or to the main hoop as close to the mounting plate as
    practically possible) diagonally opposed to the driver’s head (passenger floor).

    15.6.8 Forward Hoops (Option 1)
    The forward hoops shall extend from the main hoop (in a forward direction) to the floor
    by following the roof and the “A” pillar of the car. There shall be a bar connecting the
    two (2) forward hoops at the top of the windshield mounted as close to the roof as
    possible without violating CCR Section #15.6.20 Inspection. The forward hoops shall
    incorporate no more than four bends each. Optionally a “15.6.9 Halo Hoop (Option 2)”
    or “15.6.10 Front Hoop (Option 3)” construction may also be acceptable.

    15.6.9 Halo Hoop (Option 2)
    A “halo bar” extends from the main hoop (in a forward direction) following the roof line to
    the windshield then following along the top of the windshield, then following the roof line
    back to the main hoop, thus creating a “halo” over the driver’s head. A “halo” bar shall
    be constructed of one (1) continuous piece of tubing. One (1) down tube following the
    “A” pillar must support the “halo” on each side of the car. The down tubes shall
    incorporate no more than two (2) bends each.

    15.6.10 Front Hoop (Option 3)
    A “front hoop” is a bar that extends up from the floor, then follows the “A” pillar up to the
    roof, then follows the roof line across the top of the windshield, then back down the
    other “A” pillar, and then terminates on the floor. There must be one (1) horizontal bar
    (following the roof line) connecting the main hoop and the forward hoop on each side of
    the car. The front hoop shall incorporate no more than four (4) bends.

    15.6.11 Rear Braces
    The main hoop must have two (2) braces extending to the rear. The braces shall be
    attached as near as possible to the top of the main hoop, and no more than six (6)
    inches below the top. The braces must not contain any bends*. There must be at
    least 30 degrees between the plane of the main hoop and the plane of the rear braces.
    The main hoop rear braces shall be installed to form no more than a one hundred five
    (105) degree angle or no less than a seventy-five (75) degree angle with the main hoop
    when viewed from the top. The main hoop braces may be mounted at the rear shock
    mounts or suspension pickup points (providing that the braces remain in compliance
    with all other sections of the CCR). They may go through any rear bulkhead(s) provided
    the bulkhead(s) is sealed around the cage braces. *There may be certain exceptions
    allowed for cars that cannot possible meet this “no bend” requirement. One exception is
    listed [Ref: (15.6.11.A)]. Other exceptions may be made (not guaranteed) if all of the
    required bars meet the specifications for a vehicle in the next heavier weight
    classification and the alternative design is submitted to the NASA National Office for
    special allowance.

    15.6.11.A Rear Braces - Exceptions
    On cars where the rear window/bulkhead prohibits the installation of rear braces
    (Porsche 914, Pontiac Fiero, etc.) the main hoop must be attached to the body by plates
    welded to the cage and bolted to the stock shoulder harness mounting location. There
    must also be a diagonal bar connecting the top of the main hoop to the lower front
    passenger side mounting point (“Petty bar”). Some cars built for racing in other
    recognized sanctioning bodies may be granted a waiver of this rule, however they must
    show proof of compliance with the current published rules for their class.

    15.6.12 Door Bars / Side Impact Protection
    At least one (1) door bar on driver side and one (1) on the passenger side must be
    used. At least two (2) door bars on the driver side and one (1) door bar on the
    passenger side must be installed in all vehicles that obtain a new logbook after January
    1st, 2007.
    All vehicles, regardless of date of manufacture or date of logbook issuance will be
    required to have at least two (2) door bars on the driver side and one (1) door bar on the
    passenger side starting January 1st, 2011.
    Unless superseded by class rules, modifications to any non-chassis structure (such as
    door panels, inner door sheet metal, windows, door internals, etc.) may be made to
    accommodate any allowed door bar configuration. However, removal of material and /
    or modifications is limited to 1) the least amount to accommodate the door bar(s), and 2)
    can serve no other function. Holes in the door jam (B-pillar) may be permitted to
    accommodate door bars; however the structure should not be “notched” so as to
    weaken it.

    15.6.13 Mounting Points
    The roll cage shall be mounted to the floor area of the car in six, seven, or eight points.
    The cage shall not go through the firewall. The seventh and eighth points must attach
    to the firewall or front fender wells. All cage attachment points must be mounted to
    plates or a mounting box (plinth). Each required cage bar shall terminate on a plate with
    a 360 degree weld to the mounting plate, except as specified in Section 15.6.14.B.
    There shall be only one (1) mounting “point” per plate. This point is defined as where
    the “required tube” mounts. All additional tubes mounted to that plate must be mounted
    as close to the required tube as possible [Ref: (15.6.14.B)]. It is recommended that
    plinth boxes use a bottom support plate in cases where the edges of the box may punch
    through the sheet metal.

    15.6.14 Mounting Plates
    Each mounting plate shall be no greater than one hundred (100) square inches and no
    greater than twelve (12) inches or less than two (2) inches on a side. Welded mounting
    plates shall be at least 0.080-inch thick. Plates may extend onto vertical sections of the
    structure. Any mounting plate may be multi-angled, but shall not exceed one hundred
    (100) square inches total including vertical sections. Each mounting plate should have
    an area of not less than nine (9) square inches.

    15.6.14.A Mounting Plates – Bolt-In Cage
    The attaching points of a bolt-in cage to the body must use reinforcing plates to
    sandwich the body. At least three (3) bolts are required for each bolt-in plate and the plate must be at least 3/16 inch thick. All hardware must be SAE Grade 5 or better with
    5/16” diameter minimum. All nuts must be held securely by a locking system such as
    safety wire, lock washer, Nylox, or jam-nuts.

    15.6.14.B Tube / Mounting Plate Specifications
    Any number of tubes may attach to a plate so long as they are touching each other at
    the plate. There may be a small gap between tubes to allow welding 360 degrees
    around each tube. If there is no gap between the tubes, they must be welded around
    the base as much as possible to form a single figure-eight weld, AND the tubes must be
    welded to each other two (2) inches up from the base plate.

    15.6.15 Welds
    All welding must be of the highest quality with full penetration and shall conform to the
    American Welding Society D1.1, 1994 Edition, Structural Welding Code, Chapter 10,
    Tubular Structures and Standards for the material used. Arc welding should be used
    whenever possible. It is strongly recommended that the welder inspect all welds using
    Magnaflux™, x-ray, or other effective methods. All tubes must be welded 360-degrees
    around the circumference of the tube.

    15.6.16 Tube Structure Design / Body
    Tubes may touch the body in any place (not to violate CCR section #15.6.20
    Inspection), but shall not be attached anywhere except as permitted by CCR Section

    #15.6.11.A Rear Braces- Exceptions. No deformation of the interior body panels is
    permitted, except that the horizontal part of the sheet metal (next to the driver’s and/or
    passenger’s head) between the top of the “B” pillar and the top of the “A” pillar, may be
    pushed in to accommodate the roll cage. The intent of this allowed deformation is
    strictly to allow for more headroom for the driver and/or passenger.

    15.6.17 Additional Reinforcement
    Any number of additional reinforcing bars are permitted within the structure of the cage
    provided that they are installed strictly for safety and do not violate CCR Section #15.6.2
    Intent. This rule does not permit reinforcements in classes with spec cages.
    All required bars must be made of the same material and meet with at least the
    minimum specifications for size and thickness.

    15.6.18 Roll Cage Tubing Sizes
    For the purposes of determining roll bar tubing sizes, vehicle weight is as raced, but
    without fuel and driver. Note: There is an allowance of minus 0.010 inches on all tubing
    thicknesses. Minimum tubing size for the roll cage is:

    Up to 1500 lbs.
    1.375” x 0.095” Chrome-moly / Seamless mild steel (DOM)

    1501 - 2500 lbs.
    1.500” x 0.095” Chrome-moly / Seamless mild steel (DOM)
    1.500” x 0.120” ERW* (No issuance of log books for cars with ERW cages 04/30/03)
    *Note- Specifications listed for reference for inspection of grandfathered vehicles.

    2501 - 3000 lbs.
    1.500” x 0.120” Chrome-moly / Seamless mild steel (DOM)
    1.750” x 0.095” Chrome-moly / Seamless mild steel (DOM)
    1.750” x 0.120” ERW* (No issuance of log books for cars with ERW cages 04/30/03)
    *Note- Specifications listed for reference for inspection of grandfathered vehicles.

    3001 - 4000 lbs.
    1.750” x .120” Chrome-moly / Seamless mild steel (DOM)
    No ERW allowed.

    Over 4000 lbs.
    2.000” x 0.120” Chrome-moly/Seamless mild steel (DOM)
    No ERW allowed.
    15.6.19 Bending Allowances
    If the maximum number of bends permitted for any one bar is exceeded, all required
    components shall be made from the tubing size listed for the next heavier category and
    must be approved by a NASA race tech shop or scrutineer.

    15.6.20 Inspection
    A 3/16-inch inspection hole must be drilled in each of the required bars in a non-critical
    area for the purpose of determining wall thickness. All welds, except those mounted to
    plates on the floor, must be accessible for inspection (360 degrees).

    15.6.21 Head Support-Rear
    This section applies to seats without an integral headrest. A head restraint must be
    used to help prevent whiplash. The head restraint should have a minimum area of
    thirty-six (36) square inches and be padded with a non-resilient material such as
    Ethafoam or Ensolite with a minimum thickness of one (1) inch. It is recommended that
    padding meeting SFI specification 45.2 be used.

    15.6.22 Seat Back Support
    A seatback support must be made to hold the seat from going back in the event of a
    crash. A plate should be used to distribute the load. No bolts, corners, or sharp objects
    should be placed in such a manner that could lead to a possible puncture of the driver in
    a high impact crash. Proper design and installation is crucial to safety and it is
    recommended that the driver employ the services of a professional race car builder for
    this, as well as all other vehicle safety items. An exception may be made for those
    seats homologated to, and mounted in accordance with, FIA 8855-1999 standards.
    Those seats that qualify for the aforementioned exception must conform to the entire
    FIA 8855-1999 set of regulations. This includes a mandatory seat replacement, or use
    of a seat back brace, for any seat more than five (5) years old. Please reference the
    FIA regulations. http://www.fia.com/
    Last edited by speedminded; 12-26-2009 at 08:37 PM.

  6. #6
    YOURMOM tnomud's Avatar
    Join Date
    Mar 2005
    Location
    Coweta
    Age
    50
    Posts
    2,414
    Rep Power
    24

    Default

    Keep in mind, many sanctioning bodys will allow cars to be grandfathered in.

    Personally, I have seen many IT cars do into wicked barrel rolls over the years, and have yet to see any road racing cage fail to date. However, I have seen plenty of NHRA tech-passed cages fail..............

  7. #7
    Senior Member | IA Veteran Elbow's Avatar
    Join Date
    Mar 2005
    Location
    Atlanta
    Posts
    29,397
    Rep Power
    65

    Default

    I didn't say it said no "pro" cars I mean most FIA touring cars and such don't have the same cage rules the CCR says in what you just posted.

    Did you copy that DIRECTLY FROM the CCR? It says somewhere any cars in HPDE WITH a rollover device must meet the same rules for race cars.

    Mainly this was a vent on NASA officials and such saying a ex BTCC car isn't legal for NASA competition. The photo of the cage I posted follows almost nothing you posted meaning it'd be "illegal" even though it's legal for international professional racing.

  8. #8
    Senior Member | IA Veteran Elbow's Avatar
    Join Date
    Mar 2005
    Location
    Atlanta
    Posts
    29,397
    Rep Power
    65

    Default

    Quote Originally Posted by tnomud View Post
    Keep in mind, many sanctioning bodys will allow cars to be grandfathered in.

    Personally, I have seen many IT cars do into wicked barrel rolls over the years, and have yet to see any road racing cage fail to date. However, I have seen plenty of NHRA tech-passed cages fail..............
    Well that was my argument that they should be able to, especially if it had a FIA homligated cage (FIA rules are much different). I've seen Daytona Prototypes and such competing in SCCA events and I doubt those cages are the same spec as a other SR cage.

  9. #9
    www.jasontbarker.com speedminded's Avatar
    Join Date
    Nov 2003
    Posts
    22,589
    Rep Power
    52

    Default

    Quote Originally Posted by simontibbett View Post
    I didn't say it said no "pro" cars I mean most FIA touring cars and such don't have the same cage rules the CCR says in what you just posted.

    Did you copy that DIRECTLY FROM the CCR? It says somewhere any cars in HPDE WITH a rollover device must meet the same rules for race cars.

    Mainly this was a vent on NASA officials and such saying a ex BTCC car isn't legal for NASA competition. The photo of the cage I posted follows almost nothing you posted meaning it'd be "illegal" even though it's legal for international professional racing.
    11.4.7 says "(All cars with full roll cages should conform to the applicable sections found in section #15.0.)" then I pasted in the entire section 15 regarding roll cages...

    Research & develop continuesly changes safety devices, how they are made, and the rules regarding them so I'm not surprised a cage that was build 20 years ago wouldn't be legal to today's standards.

  10. #10
    Senior Member | IA Veteran Elbow's Avatar
    Join Date
    Mar 2005
    Location
    Atlanta
    Posts
    29,397
    Rep Power
    65

    Default

    Quote Originally Posted by speedminded View Post
    11.4.7 says "(All cars with full roll cages should conform to the applicable sections found in section #15.0.)" then I pasted in the entire section 15 regarding roll cages...

    Research & develop continuesly changes safety devices, how they are made, and the rules regarding them so I'm not surprised a cage that was build 20 years ago wouldn't be legal to today's standards.
    Right, FIA homligation for a cage at least for a pro series car ends after a certain time I believe as well. However, it will still have an FIA homligation stamp and log book...so it seems it should be allowed to come in, just like you could run a old ERW tubed bolt in cage in a car that was log booked before whatever date stated.

    I am sure there is a way lol I was just starting a random vent on why it makes no sense. Even a current day FIA built car doesn't meet these rules.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
ImportAtlanta is a community of gearheads and car enthusiasts. It does not matter what kind of car or bike you drive, IA is an open community for any gearhead. Whether you're looking for advice on a performance build or posting your wheels for sale, you're welcome here!
Announcement
Welcome back to ImportAtlanta. We are currently undergoing many changes, so please report any issues you encounter with the site using the 'Contact Us' button below. Thank you!