I just got it yesterday. Any suggestions on what would make it look better or ne comments u may have on it let me know.
![]()
I just got it yesterday. Any suggestions on what would make it look better or ne comments u may have on it let me know.
![]()
TAKE OFF THE RIMS, VINYLS, PUT ON SI FRONT/TAILS AND REAR DISK CONVERSION
FUCK B&D COMMUNICATIONS!
AND GO SLAP WHATEVER BUFORD HIGHWAYDIAN YOU BOUGHT IT FROM LOL
FUCK B&D COMMUNICATIONS!
Originally Posted by b18hatch
yess and slamm it !!!!
project- boost coming soon!
THEN GET A REAL MOTOR....OR BOOST....
OR BOTH MAYBE?
FUCK B&D COMMUNICATIONS!
Lambo doors altezza lights...
Slammed and boost. 2 things that would greatly improve it.
thanks for the constructive feedback...I only bought it for 2300 so I couldnt pass up a deal like that. but I will keep the thought of what to do in mind
thats not bad then..whats wrong with it?
FUCK B&D COMMUNICATIONS!
nothin at all amazingly I bought it over by gainsville on what we call mexico city...but all I need to do is put in a power steering belt would remove the decals but the paint stuck to them on one side so I will probably just leave them on till I get money for paint.
dx doesnt come with power steering......
youre wrong..my 95 had it factoryOriginally Posted by cadcivic
FUCK B&D COMMUNICATIONS!
plus im sure he wouldnt say he needed a belt if a pump was non existant...
caseyT, i was assuming that...i saw the car the other day on 985 going that way....just didnt want to offend mexicans by the generalization
FUCK B&D COMMUNICATIONS!
thats weird then.my 97 didnt come with it
yup. i got mine from a old lady who i know wouldnt have bought it without PS then sold it awhile back
FUCK B&D COMMUNICATIONS!
good for the price, is it high mileage?
try using heat to remove the decals. damn that thing sits almost as high as my accord![]()
^^^^ yeah the heat will take it off My dad owns a viynl shop and I have to use a heat gun, or hair dryer on everything.
-If You Own A Honda And Say "Headers", Go Jump Off Bridge...........
Take off those questionable graphics and lower it a bit, and you will be set as far as appearance. Performance is another issue.
G37s 6MT/coupe
remove graphics before anything... 9111111111111111111
Yea, I tried using heat by blow dryer and Im assuming that the person that had it before me had just tried to rip them off...so I will leave them on it till I can afford paint it has 140k but it runs great, shifts smooth, and sounds good so all and all good buy.
Yea thats the first thing id figure id here from putting the picture on this...thnks for the feedback
slam it on some si's!!!!!! don't put an after market muffler until it has a setup that actually needs it!!!
I havnt planned on putting a muffler on it yet....
does anyone know about how many inches I should lower it
sell it and get something else
"i made an RB20 into a table once...sadly it exploded two days later killing three cats" - brads94accord
I hope you are kidding....Originally Posted by dELfONiK
Land Rover LR3 HSE
it depends on if you are planning on doing it right or not. Any more than 1.25-1.5" and you will definitely want to install a camber kit as well. Also, the lower you go, the faster you will wear out the factory struts. Get a setup that either includes or will allow the use of aftermarket struts. For street driven cars, I would go no more than a 2" drop. go with good name brand springs if you do not want them to sag after 10k miles. tanabe are ok, skunk2 are decent, eibach are the best IMHO, or a set of Tein springs would work good.Originally Posted by caseyT
Land Rover LR3 HSE
dude a 2 inch drop for some reason on a civic is a little too high go lower like 2.5 or 2.75 with a type r lip or the mugen lip
by the way if you want to make your car look like the one in your sig. forget what i said on the top i dont like to ricers
FYCN in a rick james voice
Lose graphics, lose rims, lower, i/h/e.
There's your starting point.
boost the hell out of it swap it lip it and switch the rims take off the mex graphes drop it and sweetness
TAKE OFF ALL THE BULLSHIT!
for real though... F&F vinyls and rims gotta go...
Burn the wheels if you can.
BRB, The Dirty Octopus™![]()
^I second the rim burning.
take off the vinyls even if paint comes off in the process- the car is black so you can always spray paint it![]()
Originally Posted by SSMTL01
i guess whatever works huh?
BRB, The Upchucka Mutha Ucka!![]()
paint the rims black... and slam it. Get some si tail lights and front end. Tint the windows like 15% and it'll look good. Regardless of the design. I'd rather have a shitty design than mess up the paint on a car.
I wish my design on the mustang wasn't painted on the fkn thing.![]()
2014 | Hyundai Veloster | Turbo R-Spec
Sell it and buy an EX. It'll cost the same. lol
My 2001 Acura 3.2CL Type-S
Val for president!
Yes, I would have voted for her.
In loving memory of Valerie Antranikian.