GSR cams VS. B16 cams

[LongLiveH2b]

delete, this thread makes no more use

[dc2teg2006]

here is a website that tells you about the different cams and motor spec!! scroll to the middle it will tell you about the cams.

http://www.nof3ar.cjb.net/

[b17a1db2]

i've swapped out my b16 cams for gsr cams. I say it wasn't worth changing them, cause there wasn't a noticable difference to me in overall acceleration.. there was a little more midrange around 5k or so..

[bRiAnMcIvIcS]

Just go buy some ITR-CTR 00'-01' spec cams. Those are the best honda OEM cams. The gsr are slightly better than the b16, but not worth the swap.

[preferredduck]

Just go buy some ITR-CTR 00'-01' spec cams. Those are the best honda OEM cams. The gsr are slightly better than the b16, but not worth the swap.

nope get a set of CTR cams, they open more on intake side, but if you combine the CTR intake cam with a ITR exhaust cam i think thats the best bet, i'll look it up. after looking it up the ctr cams have more duration and i do believe they are a little more aggressive. remember 185hp out of a 1.6= 115.6/liter. heres the link to compare. and remember, put the dual valve springs on the exhaust side if your gonna rev, or to do on the safe side.

http://asian_e.tripod.com/Honda_Engine_Specs.htm

[Ch0psticks11]

i hear that the gsr cams are supposed to be some of the best oem cams for boost

[UpSideDownDesi]

b16 are more for top end compared to GSR, but for boost GSR FTW

[TallGuy]

on my old crx i replaced the b16 cams with the b18c cams and noticed a good bit of mid range power. but I had the a1 and a be leave it has the weakest cams for the b16 line.

[preferredduck]

on my old crx i replaced the b16 cams with the b18c cams and noticed a good bit of mid range power. but I had the a1 and a be leave it has the weakest cams for the b16 line.

you are right. on the 2nd gen b16 the intake cam is way better. look at the link above. i noticed a difference after putting the jdm b16 in my si vs the us spec b16a2. the intake cam loves my aebs manifold and intake. thats my opinion.

[Berta]

i would say the gsr cams are better for na(in a b16) and better for boost than the b16 cams.

[KevinT707]

GSR cams are cheap $60ish and it made a difference on my OBD0 B16, 3-4 WHP/WTQ when I had it dynoed before and later. OBD0 B16 cams are the worst, OBD1 B16 cams aren't too bad but GSR is better than both.

[ash7]

why waste the time in installing a cam that will only give (according to kevin's dyno) extremely minimal gains? (and i use the word "gains" very loosely there)

If one is considering a cam upgrade, at the very least take PrefferedDuck's advice... that will be a nice turbo cam setup, or a relatively low level NA setup.
-jonathan

[preferredduck]

why waste the time in installing a cam that will only give (according to kevin's dyno) extremely minimal gains? (and i use the word "gains" very loosely there)

If one is considering a cam upgrade, at the very least take PrefferedDuck's advice... that will be a nice turbo cam setup, or a relatively low level NA setup.
-jonathan

i have wanted type r cams in my car ever since the motor swap. on the first drive you heard a lot more from the front of the car than before and i know a type r intake cam is aggressive for an n/a build. gsr would be better for boost?? i've seen more turboed b18's than b16's.

[hondaxpurt]

ITR cams ftw!!!!

[ash7]

ITR cams ftw!!!!

RM M24x > ITR/CTR cams

-jonathan

[EK Hotch]

^^^Yeah!! Why is everybody turboing b18's and not too many b16's?!^^ My wife has a b16 in her del sol and I have a couple gsr heads lying around.....was thinking about throwing those b18 cams in her b16......does that sound like a good idea?

[smote]

it is not worth the time or the effort to change your stock cams to anything less than type r cams. plain and simple

[Tech5]

!!!!!!!!!!!!! AGREE!!!!! Get you some damn type r cams an be done with it!!!!

it is not worth the time or the effort to change your stock cams to anything less than type r cams. plain and simple

[killerdx]

yea iv been thinkn bout what to do to my b16 to ad a lil extra pep, so i guess il hunt me down some itr cams. Whats this about one itr and one ctr?

[smote]

that will work too. there is no big difference in any of the type r cams. I believe CTR's are the biggest though. You wouldn't notice a difference from any one type R cam to another.

[Rsxguy]

put some itr cams

[Tech5]

01 Model though!! change the valve springs on the exhaust side also !

put some itr cams

[Mr2raceworks]

Skunk pro stage 1 thats all you need to know about cams

[Ricer]

from what i understand... if you have a B16A2... GSR cams will help... but the gains are very minimal.. but if you have any older version of the b16... they'll give you a few more hp... but like everyone said.. if you're gonna go through the work of changing cams... go for something better

[LongLiveH2b]

thanks for all the comments, i just purchased crower stage 2's for my setup so thanks for all the info and stuff thanks!!!!

[smote]

you should be happy with them. I have some stage 3's and I love them