Vteckidd
08-28-2006, 11:57 AM
Here are a few things i have laying around the shop i need to unload.
First up is a D16Z6 Tranny. Tranny has an issue. It works in EVERY Gear fine, no grinds what so ever. However, the 2nd gear started to get REAL mushy going into it. Like if you went in to second it felt mushy, not as crisp as the other gears. I suspect the selector is worn out. NEVER GRINDED or popped out of gear EVER. Case is Cracked as well.
Worst case scenario, its got a good diff, 1,3,4,5,r. Perfect to rebuild your grinding D series Trans
http://i24.photobucket.com/albums/c21/Vteckidd/Picture122_800x600.jpg
$50 FIRM
Skunk2 PRO1 Camshafts
Less than 2000miles on them, PERFECT SHAPE
$450 FIRM
http://i24.photobucket.com/albums/c21/Vteckidd/Picture125_800x600.jpg
82mm GSR OEM Built Shortblock
Block Code 5601538
ITR Pistons
CP Ringset
ACL Race Bearings
Balanced and Blueprinted Rotating Assembly
New Oil Pump, Water pump, lower gasket kit
PROFESSIONALLY ASSEMBLED BY DFE ENTERPRISES
This motor made 201whp/136TQ with PRO1s and a RMF header. Motor has 2000 miles on it, PERFECT shape.
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wMTE1NDY2NjZzNDEzZGZkMzF5NTQx.jpg
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wMTE1NDY2NzZzNDEzZGZkMzF5NTQx.jpg
http://i24.photobucket.com/albums/c21/Vteckidd/KieronGSR.jpg
$1000 FIRM
First up is a D16Z6 Tranny. Tranny has an issue. It works in EVERY Gear fine, no grinds what so ever. However, the 2nd gear started to get REAL mushy going into it. Like if you went in to second it felt mushy, not as crisp as the other gears. I suspect the selector is worn out. NEVER GRINDED or popped out of gear EVER. Case is Cracked as well.
Worst case scenario, its got a good diff, 1,3,4,5,r. Perfect to rebuild your grinding D series Trans
http://i24.photobucket.com/albums/c21/Vteckidd/Picture122_800x600.jpg
$50 FIRM
Skunk2 PRO1 Camshafts
Less than 2000miles on them, PERFECT SHAPE
$450 FIRM
http://i24.photobucket.com/albums/c21/Vteckidd/Picture125_800x600.jpg
82mm GSR OEM Built Shortblock
Block Code 5601538
ITR Pistons
CP Ringset
ACL Race Bearings
Balanced and Blueprinted Rotating Assembly
New Oil Pump, Water pump, lower gasket kit
PROFESSIONALLY ASSEMBLED BY DFE ENTERPRISES
This motor made 201whp/136TQ with PRO1s and a RMF header. Motor has 2000 miles on it, PERFECT shape.
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wMTE1NDY2NjZzNDEzZGZkMzF5NTQx.jpg
http://www.we-todd-did-racing.com/wetoddimage.wtdr/wMTE1NDY2NzZzNDEzZGZkMzF5NTQx.jpg
http://i24.photobucket.com/albums/c21/Vteckidd/KieronGSR.jpg
$1000 FIRM