FS/T: 1991 Integra LS Black/Tan Interior Set w/seats

[stackz]

I've got a black/tan interior set with matching seats from a 1991 Integra LS Special Edition.

I was going to use it in my 93 civic hatch but I realized I'd have to butcher the front seats to get it to work as well as my civic brackets for the back seats.

Anyway, You get the door panels with the matching tan inserts, the quarter panel tan inserts, and both the front/rear seats in black/tan. You also get the hatch area carpet that covers the spare tire and goes on the back of the upper rear seats.

The only thing I've cleaned thus far is the back seats. Front seats are still nasty as are the door panels but they will clean up very nicely if you do them the same way I did the rears (take them apart and toss the covers in the washing machine, then re-assemble).

As everything sits, I want $75 for everything. If I have to do the work to the front seats and door panels, then I'm going to want $165.

I'll have new pics up tonight as I'm at work right now but here's an older pic of the back seats before they were cleaned.
http://x10.putfile.com/4/9918562297.jpg

http://x402.putfile.com/4/11918193387.jpg
http://x402.putfile.com/4/11918240740.jpg
http://x402.putfile.com/4/11918245216.jpg

[stackz]

Bump, if someone comes and picks it all up TODAY, I'll it all go for $30

[DC2NR]

just wondering how the hell you got the backs to fit in the civic .. bump

[stackz]

actually, they are just sitting in there right now. since the front seat rails would have required so much fab work to get to fit right I decided to just abandon using the DA seats and am going to go with s2k seats like I had in my 98 and use the black vinyl civic rear seats.

but back to the original question...

the lower I just cut outwards from both original slip mounts about another inch since the lower's front slip mounts are an inch outward. the rear lower hold-down bracket I just drilled a hole and used a selftapping screw.

the uppers actually fit the contour of the civic panels perfectly even though they physically fit in there tight. You have to cut/reweld the center body pivet mount from the civic over left about 4". Then you can just use the upper outer DA seat brackets on the inside with it. For the outer brackets, I was going to use 92-95 civic coupe upper outer brackets and just put a lock nut on the inside of the body mount.

buttt...I was saving all this fab work until after I tried the front seats out and to see if I would swap rails/pans/etc. Its going to prove to be too much work and I want my interior to match so I said oh well.

Wish I could have gotten it to work without much fuss though since I really wanted the tan/black interior with the blue/teal exterior paint. Not to mention the seats are comfy as well :D

[DC2NR]

hmm funnie .. i have DA fronts in my hatch .. and i didnt do any mods to it .. only thing is .. is that i only have 3 bolts in it .. was going to do the rears but my funds just arent enough for it right now .. looks good though .. bump for you :goodjob:

[stackz]

only thing I can think then is the floorpans must be different because I could only get two bolts in. the other two were off by more than 2" each and twisting the seat around didnt help since it would cause the rails to bind.

[LQQKITZME]

it takes only 20 mins to change the rails...

[stackz]

I'd love to know how you can change these rails in 20 minutes.

the rails on my civic seats bolt to the sides of the seat pan and are 5" wider in track.

the rails on these integra seats bolt to the bottom support of the seat pan and are 5" narrower in track. Not to mention the seat pan is completely different than the civic pans. instead of having a dip in sheetmetal pan, they have a spring-laced flat pan.

I also looked at doing what I did with the s2k seats in my 98 and swapping the entire pans out but the integra pan runs up the entire side of the seat with no bolt places where the lever to tilt is...the civic only comes up about 4" and then uses bolts.

they just arent compatible...I must have gotten a weirdo set of DA seats :(

[BLk92DA]

$10? and i come and unistall errthang myself right now

[stackz]

lol, what the hell, make it $15 and you have yourself a deal just so I can get it all out of my garage.

but I need you to come by tomorrow. I'm getting ready to go out to dinner tonight.

oh and I leave town tomorrow at $5:30p.m. so let me know if you can come by between 3:30-5:30...

[stackz]

guess he cant swing $5, oh well....


bump!

[hondagod2]

if you still have the seats call me 6785178282

[2.0civic]

if you have the fronts, ill take them tonight.

[stackz]

I'm out of town in charleston, sc painting one of my other cars guys. I'll be back in town on sunday. I prefer to get rid of the entire set together and yeah, I'll do $15 picked up for everything.

[stackz]

bump and updated the post with pics of the rest of the interior parts. I know somebody wants these for this price.:goodjob:

[MidLifeCrisis]

damn dude, if i have some free time tommorrow, ill try and setup coming and getting them.

[2.0civic]

will these fit an EF without alot of shit done to it??

[stackz]

no clue if they'll fit an EF :confused:


and yeah come by today and get them, I really need the room in my garage to work on stuff

[stackz]

dear god?? nobody wants a full black/tan interior for $15??

oh well, if I dont get any takers by friday they're going to goodwill so I can get my tax write-off

[stackz]

bump