PDA

View Full Version : Scooter Project



Athens_Red_Rexin
10-26-2013, 12:17 PM
Well it's getting colder and I decided to stop and tear down the scoot. There's a ton of things I have wanted to do to it, and a lot of things wrong with it. I bought this scooter for $100 and I did probably $200 worth of work to it to get it rideable. It was mistreated horrible by the original owner, and though it's a cheap Chinese scooter I like it. I see a lot of potential in it, and I could never justify spending thousands on a Ruckus. The only mods I have done so far are a better carb and Uni air filter, exhaust, and lowering it. My plans now are to clean up and paint the frame, remove the big lower kick stand, fix the kick start and delete the battery and starter, wire tuck through the frame, bmx stem and handlebars, and go lower all around. I have put around 1000 miles on it and love this thing. So I figure I would start this thread and keep progress on what I am doing to it. Leave a comment and let me know what you think, and suggestions are welcome for sure. Thanks!!! :goodjob:

http://i41.tinypic.com/14yafx3.jpg

http://i43.tinypic.com/99nhfp.jpg

http://i40.tinypic.com/qq8n7b.jpg

http://i39.tinypic.com/2cegggp.jpg

http://i40.tinypic.com/72fwoz.jpg

http://i42.tinypic.com/5ozej7.jpg

http://i43.tinypic.com/ic0fmr.jpg

http://i44.tinypic.com/do3x9u.jpg

http://i41.tinypic.com/34hxe9d.jpg

http://i44.tinypic.com/31775nb.jpg

http://i44.tinypic.com/20hn6fd.jpg

http://i44.tinypic.com/30bzfcn.jpg

http://i42.tinypic.com/23i6zyh.jpg

http://i43.tinypic.com/21aihsj.jpg

http://i39.tinypic.com/2czr413.jpg

Here is mock up on the BMX stem and bars.
http://i42.tinypic.com/2yn5oaf.jpg

And here are some of the tabs I plan to remove.
http://i40.tinypic.com/dq19qp.jpg
http://i40.tinypic.com/j0ek37.jpg
http://i40.tinypic.com/2uelavp.jpg

D3UC3S
10-26-2013, 02:38 PM
You always have a cool project going on. Good luck man!

Athens_Red_Rexin
10-26-2013, 02:57 PM
You always have a cool project going on. Good luck man!

Hey thanks man! I always have to be busy working on something! Drives my wife crazy :lmfao:

D3UC3S
10-26-2013, 03:20 PM
Mine too! She gets mad bc the garage always smells like gas or oil! Haha!

C230K
10-27-2013, 02:47 PM
how many cc does this one have?

Athens_Red_Rexin
10-27-2013, 07:15 PM
how many cc does this one have?

It's a 150cc GY6. Same engine that lots of guys swap to their Ruckus.

C230K
10-27-2013, 08:41 PM
Very nice, I have a toa toa scooter with on 50cc :(

Athens_Red_Rexin
10-28-2013, 07:41 PM
Well I got some of the tabs cut off today, and also cut off the huge kick stand bracket on the bottom.

http://i41.tinypic.com/1z65kdk.jpg

http://i40.tinypic.com/9rnmgk.jpg

http://i40.tinypic.com/jv2eyd.jpg

http://i42.tinypic.com/352kjmr.jpg

http://i43.tinypic.com/27yahj6.jpg

Athens_Red_Rexin
10-30-2013, 08:02 PM
Well had to stop and do a little mock up and see exactly what I want to do here. I have seen where if you slam the front all the way the forks hit the glove box, and you'll have to cut it out. Looks like that's the case here! :yes:

http://i39.tinypic.com/sgts1k.jpg

http://i43.tinypic.com/2q23khx.jpg

Here is an idea of the stretch. It's not extreme or anything, only like 4" or 5". I will have to make new motor mounts and move the shocks to the rear of the frame. I also will be moving the gas tank up in front of the engine out of the way. I am moving the license plate down to the left side of the rear tire.

http://i42.tinypic.com/2mxis6h.jpg

http://i44.tinypic.com/29lz4bd.jpg

http://i41.tinypic.com/2j4by2w.jpg

:goodjob::goodjob::goodjob:

D3UC3S
10-30-2013, 08:06 PM
Sick

Athens_Red_Rexin
11-10-2013, 03:45 PM
Heres a little update on the progress. I got the new license plate bracket made, got some mountain bike handlebars for it, cut the motor mounts to relocate them, and have made a lot of decisions on how I want it to look. I decided to put mostly all of the body panels back. I was going to leave it a naked frame like a ruckus, but it's not a ruckus! I will be ordering a lot of parts next week and here's the way it's looking now.

New tag location.
http://i40.tinypic.com/ra6tc6.jpg

Flipped the carb around so much more room now for activities!
http://i42.tinypic.com/2zqtxyb.jpg

Cut and flipped the motor mounts to relocate them.
http://i44.tinypic.com/6xvlp2.jpg

My Password JDM bmx stem shim kit.
http://i41.tinypic.com/25k1xjb.jpg

More shaving and grinding on the frame
http://i41.tinypic.com/2lcmhjn.jpg

The new stance with all the body panels back on, and the drag bars.
http://i44.tinypic.com/2w39imf.jpg

http://i40.tinypic.com/2m5gh08.jpg

Athens_Red_Rexin
11-16-2013, 01:11 PM
Here's another update...

I got my GPS mount and hardwire kit in. The GPS will be my speedo.

http://i42.tinypic.com/2elsdva.jpg

I got the motor mounts cut off and getting ready for the stretch.

http://i42.tinypic.com/x1gb6h.jpg

http://i41.tinypic.com/3012ek5.jpg

http://i43.tinypic.com/2njhydh.jpg

I also got my new blinkers in. They will be mounted on the sides of the front end.

http://i40.tinypic.com/2pzgtvd.jpg

Echonova
11-16-2013, 02:47 PM
Holy Hell! Looks bad-ass!

Athens_Red_Rexin
11-18-2013, 05:15 PM
Well finally got the motor mounts welded back on.:goodjob: And made a huge parts order with lots of goodies coming in this week. Already got some of it. Check it out.

The motor mounts welded back to the frame.

http://i43.tinypic.com/wchfdi.jpg

http://i44.tinypic.com/ip9u7t.jpg

Here's a mock up of the new rear shock mount location. I am running a rigid rear setup.

http://i40.tinypic.com/23w1qo3.jpg

http://i43.tinypic.com/34no8ap.jpg

And my new NCY ball bearing throttle and grips.

http://i40.tinypic.com/29gegrr.jpg

Scotsman
11-18-2013, 06:43 PM
Bad ass!

Athens_Red_Rexin
11-18-2013, 07:35 PM
Bad ass!

Thanks bro!!!

Scotsman
11-19-2013, 04:41 PM
still never got to see the end of the last project

Athens_Red_Rexin
11-19-2013, 06:55 PM
still never got to see the end of the last project

Oh crap which one was it??? LOL

Scotsman
11-19-2013, 07:10 PM
the mower i think

Franco Tirador
11-19-2013, 10:33 PM
cant wait to see the end, i know coming from your hands, it's going to be sick!

Athens_Red_Rexin
11-20-2013, 08:36 PM
the mower i think

Here's a link, I think I posted the final pics a little later so you probably missed them.

http://www.importatlanta.com/forums/build-threads/332000-1972-snapper-comet-restoration.html

And I went back way later and posted pics of the chopper build finished. Figured you might have been talking about it too.

http://www.importatlanta.com/forums/car-pics/261290-little-project-i-am-working-right-now-6.html

Athens_Red_Rexin
11-20-2013, 08:38 PM
cant wait to see the end, i know coming from your hands, it's going to be sick!

Thanks man, I really appreciate it. I can't wait to see it finished either. I should be posted up more pics tomorrow of all the parts that came in today.

dragoncelica
11-20-2013, 09:11 PM
Are you from Puerto Rico?

The island is in the only place i have seen such mods on these scooters, ohh and they can outrun a Busa on the 1/8 of mile when modified the right way!

Athens_Red_Rexin
11-21-2013, 07:40 PM
Well here is an update. I got in my big order of parts, and finally got it back to a rolling chassis again.

New tires, these are more of a street tire instead of the knobby tires it has.

http://i41.tinypic.com/1zbz4nr.jpg

Here is the new handlebar setup, with the new levers, grips, throttle, and gps mount in place.

http://i42.tinypic.com/2n7in9c.jpg

http://i44.tinypic.com/fdvr7b.jpg

http://i42.tinypic.com/2s0z96h.jpg

New gasket set and cvt belt for the engine.

http://i39.tinypic.com/2z8cd3b.jpg

http://i42.tinypic.com/7316wz.jpg

And here it is finally rolling again. Got the rear shock mounts welded in today. Ignore the seat, I am getting the foam redone and get it recovered.

http://i40.tinypic.com/wlznyu.jpg

http://i44.tinypic.com/3328gzl.jpg

Echonova
11-21-2013, 07:55 PM
When you get done with the scooter could you drop by my house and weld in some floorboards in the Toyota for me?


Thanks in advance. #lulz

D3UC3S
11-22-2013, 06:38 AM
This is gonna be badass! Thanks for sharing my man!

Sinfix_15
11-22-2013, 07:07 AM
Looking pretty cool so far. That scooter looked pretty good stock too.... first one ive seen someone build that wasnt a ruckus.

Athens_Red_Rexin
11-22-2013, 10:52 AM
Looking pretty cool so far. That scooter looked pretty good stock too.... first one ive seen someone build that wasnt a ruckus.

Thanks man, I appreciate it. And thank you for realizing that. I was gonna buy a ruckus, but I figured why not make this thing awesome. :goodjob:

Athens_Red_Rexin
01-11-2014, 09:15 AM
Here's a little update on the scooter. I got the motor torn down and cleaned up with new gaskets and seals. It will be getting fresh paint as soon as the weather permits. Also got the new tires mounted, and cut the back of the cvt cover out so you can see the bell housing spinning. :goodjob:

http://i39.tinypic.com/oirkt5.jpg

http://i42.tinypic.com/2whfhw7.jpg

http://i44.tinypic.com/akub7p.jpg

http://i44.tinypic.com/2qxmds0.jpg

http://i41.tinypic.com/6gjwo9.jpg

http://i41.tinypic.com/2vwi4px.jpg

Echonova
01-15-2014, 11:19 PM
My ADD would never allow me to get all those pieces put back in the correct order.



#madprops

Athens_Red_Rexin
02-01-2014, 05:08 PM
Well here's another update. I have recently got a lot done and a lot figured out. I have almost completely finished the wire tuck, and I got a lot of stuff painted today. I also have a new seat, handlebars, and turn signal switch ordered. I'll post pics of them when they come in next week. Let me know what you think. Thanks!

Here is the throttle cable after running it through the frame, and hooked to the new ball bearing twist throttle.

http://i58.tinypic.com/ok68fs.jpg

http://i57.tinypic.com/2afy2c6.jpg

http://i61.tinypic.com/209pw2f.jpg

The new turn signals mounted on.

http://i57.tinypic.com/211kms2.jpg

Here is some pics I shot real quick while I was doing wiring.

http://i58.tinypic.com/oi6g7p.jpg

http://i61.tinypic.com/2ugnv3t.jpg

Here's the starter solenoid on the new mount I made.

http://i59.tinypic.com/2qtwhs9.jpg

Here's the pieces I painted today.

http://i62.tinypic.com/f4idxi.jpg

http://i61.tinypic.com/ih09eb.jpg

Here's the engine after bolting everything back on. Pretty happy with the turn out.

http://i59.tinypic.com/16ljp88.jpg

http://i57.tinypic.com/2lt62xx.jpg

http://i58.tinypic.com/23stdtk.jpg

D3UC3S
02-01-2014, 05:19 PM
That's is lookin good dude! Always love seeing these updates!

Athens_Red_Rexin
02-01-2014, 09:09 PM
That's is lookin good dude! Always love seeing these updates!

Thanks man! I really appreciate it.

Franco Tirador
02-04-2014, 10:16 PM
heck yeah bro!

alex14
02-05-2014, 12:01 AM
Been following the build, just wanted to let you know I dig it. keep up the good work.

Athens_Red_Rexin
03-01-2014, 04:42 PM
Been following the build, just wanted to let you know I dig it. keep up the good work.

:goodjob:Thanks man! I really appreciate it.

Athens_Red_Rexin
03-01-2014, 05:05 PM
I know it's been a while but here is a pretty big update. I have actually put around 100 miles on it, and everything works really well. Here's just some quick shots of it so you see how it looks so far. I still have a lot of little things left to do, like the kick stand, finish up the wiring, and put the head tube cap on. And I still can't decide if I should put the lower panels on under the floor board. But it's got the new seat on it, the new turn signal switch, the new renthal handlebars, a set of HID headlights, and much more. I have a bunch of stuff ordered, NCY coil pack, extended rear brake cable, some carbon fiber rear flares, and a mikuni fuel pump. I'll post up pics of that stuff next week. Let me know what you think so far. Thanks guys! :goodjob:

http://i57.tinypic.com/fdvql1.jpg

http://i59.tinypic.com/2it1kk4.jpg

http://i62.tinypic.com/9jj7me.jpg

http://i62.tinypic.com/241nu4j.jpg

http://i60.tinypic.com/2b4gw2.jpg

http://i59.tinypic.com/op1q8n.jpg

http://i59.tinypic.com/b9i3bo.jpg

Echonova
03-01-2014, 09:59 PM
Bad-ass!!!!!

alex14
03-21-2014, 11:29 PM
The Mothers kick stand is where its at.