k24eg
03-22-2012, 03:13 PM
testing waters on my motor. this motor has a few dyno pulls on it. it made 280whp with a bad alignment on a dynojet at midnight atl before my tps sensor broke on the dyno. probably could have made closer to 300.
it was tuned on e85.
i'm thinking about stepping up to a bigger motor but i would need to sell this one first.
all the parts were bought brand new. no corners were cut with this build.
87.5 bore 13.7 compression wiseco pistons
carillo pro light weight rods
acl race bearings
k24a8 block with vin still attached 100% legit was hot tanked and bored to 87.5 and balanced
all new k20a2 oil pump, chains, guides, tensioner
k24 oil pan
arp head studs
head has 3 angle valve job
supertech springs and retainers
skunk2 stage 3 v3 cams
k24 water pump
$3000 picked up or can deliver in or around atl for free
it costs way more than what im asking to build a motor like this. your looking at about $5k to have a motor like this built. its a steal at 3k! i won't take less than that so don't even ask.
i may be willing to sell the trans with it if a buyer wants the complete swap. its a 5 speed with type-r lsd. i also have a stock 6-speed.
parts that can be added for extra
k-tuned ac/ps delete $150
rc 750cc k series injectors $300
new asp ceramic coated header with megaphone and 3" v-band with clamp $900
i'm located in columbus,ga my cell is 706-593-7507. text me if i don't answer.
http://i22.photobucket.com/albums/b346/mprat1225/IMG_20120311_125253.jpg
disregard the torque, it wasn't reading right on the dyno for some reason
http://i22.photobucket.com/albums/b346/mprat1225/IMG_20120311_125238.jpg
http://i22.photobucket.com/albums/b346/mprat1225/IMG_20120311_131753.jpg
it was tuned on e85.
i'm thinking about stepping up to a bigger motor but i would need to sell this one first.
all the parts were bought brand new. no corners were cut with this build.
87.5 bore 13.7 compression wiseco pistons
carillo pro light weight rods
acl race bearings
k24a8 block with vin still attached 100% legit was hot tanked and bored to 87.5 and balanced
all new k20a2 oil pump, chains, guides, tensioner
k24 oil pan
arp head studs
head has 3 angle valve job
supertech springs and retainers
skunk2 stage 3 v3 cams
k24 water pump
$3000 picked up or can deliver in or around atl for free
it costs way more than what im asking to build a motor like this. your looking at about $5k to have a motor like this built. its a steal at 3k! i won't take less than that so don't even ask.
i may be willing to sell the trans with it if a buyer wants the complete swap. its a 5 speed with type-r lsd. i also have a stock 6-speed.
parts that can be added for extra
k-tuned ac/ps delete $150
rc 750cc k series injectors $300
new asp ceramic coated header with megaphone and 3" v-band with clamp $900
i'm located in columbus,ga my cell is 706-593-7507. text me if i don't answer.
http://i22.photobucket.com/albums/b346/mprat1225/IMG_20120311_125253.jpg
disregard the torque, it wasn't reading right on the dyno for some reason
http://i22.photobucket.com/albums/b346/mprat1225/IMG_20120311_125238.jpg
http://i22.photobucket.com/albums/b346/mprat1225/IMG_20120311_131753.jpg