OhMyGodfather
06-05-2011, 06:29 PM
For purchasing information, please contact me on here through PM, or Text me at 404-416-8192.
I have a KA-T kit. Its running custom manifold, that is T3 flange. The setup was originally made for Rb20DET turbo to be put on the KA, but it can also run the RB25 set up as well. It made 230whp and 265wtq at 13lbs boost on a Dynojet. The setup is as follows: RB20DET turbo (13lb wastegate) SR20 370cc Injectors, Z32 MAF sensor, CX Racing intercooler kit, ARC Blow off valve, 2.5 inch Downpipe. Nistune engine management (Type 3 board, tuned by Scottie at Mainstream Performance) and a Spec Stage 2 Clutch (Used for ~20 minutes of driving including dyno time. Spec says this specific clutch will hold 380ft lbs. torque) Kit goes for more, but Im very impatient and want this crap out of my garage! $1000 firm! Pics below. Also, I plan on parting it out if it doesnt sell, therefore, I listed all the individual parts for sale as well!!!!!
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/226298_10150173974051456_590761455_7385391_4312773 _n.jpg
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc6/225724_10150179085411456_590761455_7418254_2743615 _n.jpg
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc6/225561_10150179084371456_590761455_7418243_7511178 _n.jpg
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/225676_10150179084251456_590761455_7418242_5145557 _n.jpg
Dyno Vid:
http://www.youtube.com/watch?v=74kTlVqyYok
Driftin'
http://www.youtube.com/watch?v=DR5277jV7PA
CX Racing Intercooler core with couplers and ARC 1st gen BOV! Blow off valve is mounted to intercooler with studs and gasket, the silicone was added to make sure of no boost leaks. Blow off valve is RFL loud with the 25 turbo on it. Only selling because I bought a new motor and it has all this stuff on it already! ($250.)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/254041_10150196891351456_590761455_7590950_739617_ n.jpg
Z32 Maf with pigtail and Spectre 3" Filter. ($90)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc6/247333_10150196891446456_590761455_7590952_2424303 _n.jpg
Nistune Type 3 board with KA-T Tune (set up is written on outside) You can wipe it clean and have it reflashed. ($250)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/246882_10150196891616456_590761455_7590954_8051818 _n.jpg
KA24DE Engine Harness wired for Z32 maf ($50)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc6/249632_10150196891731456_590761455_7590955_6185921 _n.jpg
KA24DE Transmission. Shifts like gravy. Have a new one on my SR, and already have a spare, so no need for this. ($75)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc6/247948_10150196891766456_590761455_7590956_3355347 _n.jpg
RB25DET Turbo. No shaft play, great condition. Clocked for the KA-T kit I had it on, but can easily be adjusted back. Comes with 11lb and 9lb wastegates. ($200)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/248682_10150196891951456_590761455_7590958_5528512 _n.jpg
RB20DET Turbo. No shaft play, oil residue from blown rings in motor, other than that its groovy. Got it from a member on here, forgot his name. But it boosted fine when I had it on. ($100)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc6/250494_10150196902531456_590761455_7591072_4183053 _n.jpg
CX Racing Intercooler piping. Powder Coated black. Will fit both KA and SR on cold side, and most Top Mount turbo setups on either motor. ($50)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/255015_10150196892011456_590761455_7590959_4341449 _n.jpg
RB 20/25 Top mount KA-T set up downpipe. Looks kinda choppy but it gets the job done! O2 sensor is KA and flange is setup for S chassis. Better as a package deal obviously, but hey, its your cup of tea. ($50)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc6/252915_10150196892116456_590761455_7590960_70468_n .jpg
I have a KA-T kit. Its running custom manifold, that is T3 flange. The setup was originally made for Rb20DET turbo to be put on the KA, but it can also run the RB25 set up as well. It made 230whp and 265wtq at 13lbs boost on a Dynojet. The setup is as follows: RB20DET turbo (13lb wastegate) SR20 370cc Injectors, Z32 MAF sensor, CX Racing intercooler kit, ARC Blow off valve, 2.5 inch Downpipe. Nistune engine management (Type 3 board, tuned by Scottie at Mainstream Performance) and a Spec Stage 2 Clutch (Used for ~20 minutes of driving including dyno time. Spec says this specific clutch will hold 380ft lbs. torque) Kit goes for more, but Im very impatient and want this crap out of my garage! $1000 firm! Pics below. Also, I plan on parting it out if it doesnt sell, therefore, I listed all the individual parts for sale as well!!!!!
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/226298_10150173974051456_590761455_7385391_4312773 _n.jpg
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc6/225724_10150179085411456_590761455_7418254_2743615 _n.jpg
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc6/225561_10150179084371456_590761455_7418243_7511178 _n.jpg
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/225676_10150179084251456_590761455_7418242_5145557 _n.jpg
Dyno Vid:
http://www.youtube.com/watch?v=74kTlVqyYok
Driftin'
http://www.youtube.com/watch?v=DR5277jV7PA
CX Racing Intercooler core with couplers and ARC 1st gen BOV! Blow off valve is mounted to intercooler with studs and gasket, the silicone was added to make sure of no boost leaks. Blow off valve is RFL loud with the 25 turbo on it. Only selling because I bought a new motor and it has all this stuff on it already! ($250.)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/254041_10150196891351456_590761455_7590950_739617_ n.jpg
Z32 Maf with pigtail and Spectre 3" Filter. ($90)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc6/247333_10150196891446456_590761455_7590952_2424303 _n.jpg
Nistune Type 3 board with KA-T Tune (set up is written on outside) You can wipe it clean and have it reflashed. ($250)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/246882_10150196891616456_590761455_7590954_8051818 _n.jpg
KA24DE Engine Harness wired for Z32 maf ($50)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc6/249632_10150196891731456_590761455_7590955_6185921 _n.jpg
KA24DE Transmission. Shifts like gravy. Have a new one on my SR, and already have a spare, so no need for this. ($75)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc6/247948_10150196891766456_590761455_7590956_3355347 _n.jpg
RB25DET Turbo. No shaft play, great condition. Clocked for the KA-T kit I had it on, but can easily be adjusted back. Comes with 11lb and 9lb wastegates. ($200)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/248682_10150196891951456_590761455_7590958_5528512 _n.jpg
RB20DET Turbo. No shaft play, oil residue from blown rings in motor, other than that its groovy. Got it from a member on here, forgot his name. But it boosted fine when I had it on. ($100)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc6/250494_10150196902531456_590761455_7591072_4183053 _n.jpg
CX Racing Intercooler piping. Powder Coated black. Will fit both KA and SR on cold side, and most Top Mount turbo setups on either motor. ($50)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash4/255015_10150196892011456_590761455_7590959_4341449 _n.jpg
RB 20/25 Top mount KA-T set up downpipe. Looks kinda choppy but it gets the job done! O2 sensor is KA and flange is setup for S chassis. Better as a package deal obviously, but hey, its your cup of tea. ($50)
https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-snc6/252915_10150196892116456_590761455_7590960_70468_n .jpg