View Full Version : FS: Catch Can Setup, 96-00 civic
SPOOLIN
11-25-2010, 08:57 AM
Catch can setup for sale...Bolts to a 96-00 civic driver side wheel well. It holds about a gallon and is baffled with 2 filters. It has 3 -8 ports on top that are where the AC dryer cylinder would usually be. I have 2 of the ports connected to the valve cover. Im selling the custom can with valve cover and lines to connect it.
$300.00 OBO! ......
http://i28.photobucket.com/albums/c203/spoolinmatt/2000%20EK/Third%20Setup/P1030046.jpg
Pic doesn't show the filters in place because this was during fabrication...but there are 2 side by side, the same size as the "standard" catch can setups out there. It has a drain plug at the bottom.
http://i28.photobucket.com/albums/c203/spoolinmatt/2000%20EK/Third%20Setup/imagejpeg_0_1.jpg
http://i28.photobucket.com/albums/c203/spoolinmatt/MISC/can2.jpg
http://i28.photobucket.com/albums/c203/spoolinmatt/MISC/can1.jpg
Da_unknown
11-28-2010, 09:39 PM
ttt
Jdm94Coupe
01-05-2011, 05:13 PM
you still have this stover? will that catch can setup work for a EG? and would you sell it with just the catch can and lines w/out the valve cover? i dont have a dohc.....
SPOOLIN
01-10-2011, 06:00 PM
im not to sure on it mounting to an EG, im sure there would be a way....and you might have to trim the hole where the AC thingy was, it might differ from the EK a little. I guess i could knock off 75$ without the valve cover.
Jdm94Coupe
01-10-2011, 06:11 PM
im not to sure on it mounting to an EG, im sure there would be a way....and you might have to trim the hole where the AC thingy was, it might differ from the EK a little. I guess i could knock off 75$ without the valve cover.
ok i appreciate it, i'll let u know. i gotta look at my car and see how this would work. lol
ekredcivic
01-10-2011, 09:00 PM
sale him the can and sale me the valve cover for 75
SPOOLIN
01-11-2011, 07:57 PM
OOOOK. My car is going in for some Fabrication soon so it would be nice to have this sold by then...I don't wanna take it twice cause ill have to move my battery.
SPOOLIN
01-12-2011, 12:47 PM
it should work, the front ends are the same...other than the core support and body panels. I can't test it right now...but i might can this weekend.
xero_xero
01-12-2011, 08:18 PM
Nice setup. proprs on the custom fab. i was looking to do the same thing with the PS resevoir and Coolant Overflow.
JKOBD
01-21-2011, 09:08 PM
Bump cause this car better go 9s in 2011.
SPOOLIN
01-21-2011, 09:15 PM
lol. I was gonna bump this earlier, do work jason
SPOOLIN
01-23-2011, 01:41 PM
300$ for the catch can setup! Price Drop yo.
SPOOLIN
01-24-2011, 08:46 AM
OBO
SPOOLIN
01-25-2011, 06:05 PM
added a couple more pics, and the measurements are...
front Facing side: 2.5" wide
Back panel top: 7"
Back panel bottom: 5"
Left side panel top: 11"
Left side panel bottom 6.5"
Filter protrusion: 3.5"
SPOOLIN
01-25-2011, 07:00 PM
SOLD!!
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.