View Full Version : How to Turbo a IS (Afternoon Laugh)
TIGERJC
04-10-2010, 10:15 AM
http://my.is/forums/f114/turbocharger-turboheadache-turboclub-pics-inside-warned-alots-408894/
Wow sometimes it pays to take it to a shop especially when you dont know what the fuck you're doing
98blackcivic
04-10-2010, 10:17 AM
my sig is the afternoon laugh bish
Elbow
04-10-2010, 10:27 AM
What's wrong with it?
TIGERJC
04-10-2010, 10:33 AM
I guess is just me, but using jb weld to install a bov and using a hammer to make a hole for the piping is just funny to me. Also when he tapped the oil pan, I believe he never uninstall it so he has metal shavings still in his pan.
CHRISNITTOLO
04-10-2010, 10:34 AM
It's not the afternoon yet. You mean (Late morning Laugh) lol. W/E Those guys are dumb as shit. They're probably not even old enough to buy the Smirnoff.
TIGERJC
04-10-2010, 10:38 AM
It's not the afternoon yet. You mean (Late morning Laugh) lol. W/E Those guys are dumb as shit. They're probably not even old enough to buy the Smirnoff.
If I cant get chick fila breakfast, then its the afternoon
CHRISNITTOLO
04-10-2010, 10:50 AM
If I cant get chick fila breakfast, then its the afternoon
So is it All afternoon tomorrow? Even at 9 in the morn?
Kevykev
04-10-2010, 10:58 AM
That is something that I wish I could Un-see.
I have no more words for this...
tdurr
04-10-2010, 12:53 PM
i like the BOV the best.
Now thats fucking rice. Copy this thread into the WTF section too
e30pwr
04-10-2010, 05:47 PM
this is a pretty schweet build ya found! i'm guessing there will be a dead engine thread in a few weeks too.....
SloWRX
04-10-2010, 06:56 PM
I wanna see a build thread by him fixing the blown engine, now THAT would be interesting
e30pwr
04-10-2010, 07:43 PM
I wanna see a build thread by him fixing the blown engine, now THAT would be interesting
i forsee play dough for plasti-gauge, all bolts tightened down as hard as possible, no assembly lube, rod bearings hammered in, headstuds put in by a pair of pliers, and to top it all off wd40 as oil.
Elbow
04-10-2010, 07:44 PM
i forsee play dough for plasti-gauge, all bolts tightened down as hard as possible, no assembly lube, rod bearings hammered in, headstuds put in by a pair of pliers, and to top it all off wd40 as oil.
I only finger tight head bolts.
CHRISNITTOLO
04-10-2010, 08:12 PM
i forsee play dough for plasti-gauge, all bolts tightened down as hard as possible, no assembly lube, rod bearings hammered in, headstuds put in by a pair of pliers, and to top it all off wd40 as oil.
I only finger tight head bolts.
I use play-doe to fill in dents.
Da_unknown
04-10-2010, 08:33 PM
:no:
SLow_POke
04-10-2010, 08:35 PM
make it a sticky in the Tech section!
SLow_POke
04-10-2010, 08:59 PM
and hes defending his work!!!!!! he should work at he shop that did that rx-7 with the ls swap.......
e30pwr
04-11-2010, 01:26 AM
I use play-doe to fill in dents.
:lmfao::lmfao:
green
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.