PDA

View Full Version : do it yourself mx6 lip on EF civic



jdm-civic
03-30-2010, 11:47 AM
well i bought a lip from a mx6 and i was wondering how would you go about mounting it and making it fit proprly?

quickdodgeŽ
03-30-2010, 11:57 AM
It's made to fit an MX-6? Later, QD.

jdm-civic
03-30-2010, 12:01 PM
ive seen a few people online use these lips and they fit, i was wondering if there was any cutting or anything involved

Theycall_Metue
03-30-2010, 12:03 PM
should be bolts/screw ons
if dosnt fit, send it back for another one or.... if you drive a jdm civic it shouldnt fit at all

quickdodgeŽ
03-30-2010, 01:29 PM
Why wouldn't you just get the right piece for it in the first place? Later, QD.

5speed
03-30-2010, 01:33 PM
Take the bumper off the car and set it on a bench. Put the lip up on it to see if it is too long, which it most likely will be. Cut down exactly from the Center and repeat the first step too figure out how much to trim off of each side. That is how I have seen it done on Late 3rd gen Preludes

This is what I found for the Lude.

It's not too bad really...It's alot easier with the bumper cover off too!!

The sides fit perfectly after you cut it in half.

Here are the steps I used.

1. Cut it in exactly half.

2. Get a friend to hold both side on so the middle over lap and mark the end of one of the pieces where it overlaps the other and that is where to cut.

3. Cut the part out of the middle.

4. Use self tapping sheet medal screws to screw it securly to the bumper cover starting from the outside and working towards the middle (I used like 1000, lol) The more the better!!

5. Where it's cut in the middle, use fibreglass on the back of it to mold it together. Doesn't matter what it looks like, you won't see it. Goop it on!!

6. Use a little bodyfill or fibreglass resin fill to smooth out the front and then sand smooth.

7. Use spot putty to do the finishing touches.

DVSRX-7
03-30-2010, 06:43 PM
Why the fuck would you be soooooo fucking cheap and buy a MX-6 lip in the first place?!

I thought you were JDM

5speed
03-30-2010, 08:20 PM
It looks good on a 3rd Gen Prelude, so it probably will on an EF too. Who cares if its for another car, its not like he is trying to fit a MX-6 bumper on it.

jdm-civic
03-30-2010, 11:48 PM
Why the fuck would you be soooooo fucking cheap and buy a MX-6 lip in the first place?!

I thought you were JDM

because it was $2 at pull a part and i wanted a lips and ive seen it done before so i wanted to try it

Theycall_Metue
03-31-2010, 12:08 PM
because it was $2 at pull a part and i wanted a lips and ive seen it done before so i wanted to try it
:screwy::screwy::screwy::screwy::screwy:

StarBwoy
03-31-2010, 12:46 PM
http://www.honda-tech.com/showthread.php?t=2259952 i got a my lip from the pullapart too

jdm-civic
04-07-2010, 12:10 AM
well this is how it turned out. i had another peice of a lip cut for the middle but my driveway made sure that it didnt stay so im going to do a lil more cutting this weekend. cant beat it for $2
http://sphotos.ak.fbcdn.net/hphotos-ak-snc3/hs446.snc3/25602_379158438877_779918877_3828882_8236772_n.jpg

VickNotic
04-07-2010, 11:10 AM
that didn't make a difference at all and wassup with the black tape on the headlights?? well watever it is more kudos for you bro

punkr6
04-07-2010, 11:12 AM
LOL @ this guy....

Austin?
04-07-2010, 12:08 PM
yeah, whats the deal with black tape???

KevinT707
04-07-2010, 04:40 PM
All I've ever seen are different lips fitted onto sedan and hatch EFs, no CRX.

Is the CRX bumper much different in shape than the sedan?

jdm-civic
04-08-2010, 12:05 AM
^^not quite sure, i think they shouldnt be too different.

and the black tape is something ive been doing to everysingle car i have ever owned.its my trademark, my sign, my signal.......what make me stand out from the croud and its something i dont really see people do so therefore i do it!

mushroom_toy
04-08-2010, 01:32 AM
^^not quite sure, i think they shouldnt be too different.

and the black tape is something ive been doing to everysingle car i have ever owned.its my trademark, my sign, my signal.......what make me stand out from the croud and its something i dont really see people do so therefore i do it!

Not hating on ya too much but sorry black tape does not make you special. Tape helps keep glass off of the track, and chips off the glass. (What it should be used for.) Just a fyi. If someone reads this and dont know what I mean by the last statement...please go to a non-automotive forum.

XanRules
04-08-2010, 09:16 AM
^^not quite sure, i think they shouldnt be too different.

and the black tape is something ive been doing to everysingle car i have ever owned.its my trademark, my sign, my signal.......what make me stand out from the croud and its something i dont really see people do so therefore i do it!
I take dumps on peoples' hoods.
It's something I do to every car I've ever seen and didn't like because the owner was a faggot.
It's my trademark, my sign, my signal...what makes me stand out from the crowd, and it's something I don't really see people do, so therefore I do it.
Change bomb? QuikTrip cup? F that noise, I'm doing to drop trow and squeeze one out on your hood.
If you drive a WRX, it does wonders for the intercooler, too.

JITB
04-08-2010, 12:03 PM
LEAVE THE MAZDA PARTS FOR THE MAZDAS!!!!!!!!!!!
http://img.photobucket.com/albums/v334/jitb37/Protege/pictur3s00099002.jpg



i told u man i got a cut out piece for that lip that will fit in that piece that your missing! been selling those things for years..for my protege people! u gonna come get it or what! last time! ill give it to u as long as you dont take any more mazda parts for ur honda lol

jdm-civic
04-08-2010, 12:07 PM
LEAVE THE MAZDA PARTS FOR THE MAZDAS!!!!!!!!!!!
http://img.photobucket.com/albums/v334/jitb37/Protege/pictur3s00099002.jpg



i told u man i got a cut out piece for that lip that will fit in that piece that your missing! been selling those things for years..for my protege people! u gonna come get it or what! last time! ill give it to u as long as you dont take any more mazda parts for ur honda lol

lol! alright ill come by this saturday and get it! and if i recall there is one more mx6 lip out there

JITB
04-08-2010, 12:16 PM
naw it was messed up a little, but i got more from moreland.

jdm-civic
04-11-2010, 12:51 PM
ay were you stay

EJdm
04-12-2010, 11:00 AM
http://www.honda-tech.com/showthread.php?t=2259952 i got a my lip from the pullapart too

some of those ef looks nice with those lip

geezy
04-13-2010, 07:13 PM
a 1st generation integra lip will fit perfect .juss cut from the edges! and bolt on!

geezy
04-13-2010, 07:55 PM
I Also heard u can modify a civic ex or si lip on to a ef

OldSchool87
04-26-2010, 12:30 AM
I dont think the problem is finding a lip to fit the CRX or any EF for that matter. I'ts about finding one you like. more power to yah buddy. at the end of the day a lips a lip. its no different than the guys that have solid amber cornes on the EG calling tem JDM when we all know they were clear in Japan.

Sol-Badguy
05-02-2010, 07:59 AM
I did one on my 3rd gen Prelude. Needed two lips. The second one, to cut about 4 inches for the center section.

It would help if you paint them the same color.

jdm-civic
05-02-2010, 11:05 AM
I did one on my 3rd gen Prelude. Needed two lips. The second one, to cut about 4 inches for the center section.

It would help if you paint them the same color.

thats exactly how mines looks, just i dont have the center piece

geezy
05-06-2010, 12:51 AM
I wonder what type of ef lip this is?? looks nice tho!

http://i40.tinypic.com/5n9po1.jpg

Sol-Badguy
05-06-2010, 11:57 PM
thats exactly how mines looks, just i dont have the center piece

Just get a hold of another half of the lip, then cut to fit.

Check Pull-a-part. They want less than $10 for one.