wire tuck help

[CautionMeDC2]

Iv been wanting to do a mild wire tuck on my teg but dont knw how to start or if its even worth it. any tips, advice, or input is welcome and appreciated.:goodjob:

[dallasb84]

you only need electrical tape and some tinners snips and maybe some of that wire that comes in rolls from auto zone..... you know the black stuff...

just start cutting your wires and extend them a little bit.... then twist the wires real tight so they dont come loose and tape em up....

[AyO Deebo]

Make sure you do it right you don't want any problems. Solder the wires together don't twist them real tight and tape it lol. Put heat shrink after you solder every wire together.

[Kserieskid]

If you're looking to do I MILD tuck I believe you don't need any tape, wire, or solder. Simply route both body harness' from the shock tower under the frame rail towards the head lamps. Im pretty sure you only need adell clamps and screws and you're set. You could also route both harness' through the opposite hole where the brake line runs through. Up to you.

[RBS]

buy a notebook and record everything you do as you do it, so when you come in here asking for help we can go straight to the problem :goodjob:

[Black4DrEK]

^ haha

[CautionMeDC2]

buy a notebook and record everything you do as you do it, so when you come in here asking for help we can go straight to the problem :goodjob:

i dnt wna end up with problems?

[NoWAyItZTOMmY]

if you are just trying to tuck the passenger and driver side harness for the lights and what not.

just unplug everything and trace it back to where it enters the firewall.

pull it all through and run the wires through the door harness hole

secure the wires to the frame rail and plug everything back up

[NoWAyItZTOMmY]

if you are just trying to tuck the passenger and driver side harness for the lights and what not.

just unplug everything and trace it back to where it enters the firewall.

pull it all through and run the wires through the door harness hole

secure the wires to the frame rail and plug everything back up

[99jdmLs]

i dnt wna end up with problems?

if you ask how to do a wire tuck, and you start cutting and twisting wires together...you will hit some snags. lol.

[silverDA]

i wish i never did my tuck.

[CautionMeDC2]

if you ask how to do a wire tuck, and you start cutting and twisting wires together...you will hit some snags. lol.

havnt started yet.? :thinking: and dnt plan on cutting ne wires unless i have to extend some but i doubt it

[shane94]

i dnt wna end up with problems?

then ask Got_Purp how to do it, he did mine

[.:Stirfry:.]

If you're looking to do I MILD tuck I believe you don't need any tape, wire, or solder. Simply route both body harness' from the shock tower under the frame rail towards the head lamps. Im pretty sure you only need adell clamps and screws and you're set. You could also route both harness' through the opposite hole where the brake line runs through. Up to you.

x2 if you just doin the lights they will reach with no prob.

[.:Stirfry:.]

i wish i never did my tuck.
wwuuut?

[gerardojdm]

if you are you are planning on doing an wire tuck and asking for help then thats a big recipt for failure.... seriously!!!!!!!! leave it alone an find something else to do

[KevinT707]

Just leave it alone, leave it how Honda intended!

[H1Cblacknight]

Make sure you do it right you don't want any problems. Solder the wires together don't twist them real tight and tape it lol. Put heat shrink after you solder every wire together.


x2
had a good laugh for twisting real tight! two words electrical fire!