who does soda blasting?

[blown_ss]

does anyone know of a place that does soda blasting? southside would be nice too. thanks.

[Tech5]

Splunge!!!!

[blown_ss]

Splunge!!!!

what?

[ballistic08]

what do you need soda blasted?

[blown_ss]

wheels

[Tech5]

You know Splunge your thirst lololol

[blown_ss]

You know Splunge your thirst lololol


damn you got me.:boobies:

[Tech5]

damn you got me.:boobies::lmfao::lmfao::lmfao::lmfao::lmfao::lm fao:

[coreyctr1980]

I do it, 20 bucks and a case of Dr. pepper. It's starting to wear out my shoulder. I start by shaking the cans rapidly then throwing them as hard as i can at the car.

[blown_ss]

I do it, 20 bucks and a case of Dr. pepper. It's starting to wear out my shoulder. I start by shaking the cans rapidly then throwing them as hard as i can at the car.

haha. jokes aside. i really need to know of a place that does soda blasting.

[Slomaro Z28]

A guy I work with does it, he did my intake manifold on my z28. Came out awesome, you need 4 wheels done? I'll see about getting a price from him.

Here is the inside of my manifold after he blasted it. Not 100% like new, but damn good. Can't find the before pics, but it was nasty. Wheels should be easy for him.

http://i64.photobucket.com/albums/h187/Southernbabe0906/SDC10279.jpg

http://i64.photobucket.com/albums/h187/Southernbabe0906/SDC10272.jpg

[lanning]

heres some
Americas Preferred Sodablasters
1595 Peachtree Pkwy Suite 204-348
Cumming, Georgia 30041
Dan O'Donnell
Office: (770) 889-8211
Cell: (678) 591-0604

X-Treme K-Lean Soda Blasting

575 East Mays Road, Stockbridge, GA(770) 474-3400‎
dont know how far away that is from where you're looking

[blown_ss]

heres some
Americas Preferred Sodablasters
1595 Peachtree Pkwy Suite 204-348
Cumming, Georgia 30041
Dan O'Donnell
Office: (770) 889-8211
Cell: (678) 591-0604

X-Treme K-Lean Soda Blasting

575 East Mays Road, Stockbridge, GA(770) 474-3400‎
dont know how far away that is from where you're looking

yeah i googled and found those. i was just more so wondering if anyone has used certain shops for it. thanks for your help though.

[blown_ss]

A guy I work with does it, he did my intake manifold on my z28. Came out awesome, you need 4 wheels done? I'll see about getting a price from him.

Here is the inside of my manifold after he blasted it. Not 100% like new, but damn good. Can't find the before pics, but it was nasty. Wheels should be easy for him.

http://i64.photobucket.com/albums/h187/Southernbabe0906/SDC10279.jpg

http://i64.photobucket.com/albums/h187/Southernbabe0906/SDC10272.jpg

pmed. :goodjob:

[ballistic08]

Millers powder coating would probably sand blast them for you.

[blown_ss]

Millers powder coating would probably sand blast them for you.

no thanks

[ballistic08]

lol because you think soda blast will make a difference than a sand blast?

[dallasb84]

plastic media is better that soda....... just sayin.....

and if your really feeling like a pussy go for walnut shells....

but other than that sand blast ftw....


pmb is good for a polishable surface with no surface degrade..

walnut shells is good for finish removal of well like gold or silver..... like if you were to blast a saxophone or maybe a flute...... but......

[Humphrizzle]

i see no reason you'd rule out sand blasting over soda blasting for wheels..

[blown_ss]

lol because you think soda blast will make a difference than a sand blast?

do your research there is a difference. go take sandpaper to the lip of your wheels and see what you get. im not looking to do a major clean up after i get this done. on another note if i wanted SAND BLASTING then i would have fucking asked for it.

[blown_ss]

plastic media is better that soda....... just sayin.....

and if your really feeling like a pussy go for walnut shells....

but other than that sand blast ftw....


pmb is good for a polishable surface with no surface degrade..

walnut shells is good for finish removal of well like gold or silver..... like if you were to blast a saxophone or maybe a flute...... but......

oh i agree. the 2 are about the same but with soda i wouldnt have to refinish the surface as much as with media or sand.

[dallasb84]

at least you know what you want...... and if you do soda blast.... your hands wont be grey for a day or so from polishing or whatever you do......


good luck..... if you find a spot..... let us know and do some before and after shots of the work..... im thinking of a project i want done..... and may need something like this