bowdown201
01-07-2010, 05:10 PM
Seen a few write ups of this and decided to try it today.
What you will need: (Part numbers are from Summit Racing)
(1) pair Male -3 AN to Male 10mm x 1.0 Earls Brake Adapters EAR-592032ERL ($14.69)
http://i46.tinypic.com/34i21qp.jpg
(2) steel -3 AN swivel hose ends. Style is up to you.
I used 1 regular hose end - AER-FBM1100 ($5.25) &
1 45deg hose end - AER-FBM1110 ($10.25)
http://i49.tinypic.com/2q1thc6.jpg
(1) -3 AN braided hose 10ft length. EAR-610003ERL ($29.95)
http://i48.tinypic.com/rac7d2.jpg
(NOTE) You probably wont need 10ft of the hose (I only used bout 4 or 5ft.) but Summit was sold out of 6ft so I just got the 10ft :goodjob:
(1) DOT 3 brake fluid - any qty/brand should work
THE INSTALL
Take a 10mm wrench and unscrew the fitting like so..
http://i47.tinypic.com/nx1k0g.jpg
http://i45.tinypic.com/t6oxhi.jpg
Install the new 10mm fittings. (NOTE: That notch of the block may get in your way a little but not so bad to where it wont screw in the threads. Just make sure you get it started good)
http://i49.tinypic.com/14ad1dh.jpg
I then mapped out where I wanted to run the line. I wanted easy access to it so I just ran it over the top of the tranny back behind the T Bracket, behind all the hardline brakelines and over the brake booster.
I had a lot of excess hose so I tapped off where I wanted to cut it and used a punch and hammer to cut it like so..
http://i45.tinypic.com/ka61yd.jpg
Install the braided hose to the hose ends. Check this link (http://www.anplumbing.com/SWIVEL_SEAL_HOSE_ENDS.html)for install instructions.
http://i48.tinypic.com/246mmwl.jpg
http://i50.tinypic.com/fp8rhw.jpg
Then just run the line where you want it and hook up the hose ends and VOILA!
http://i48.tinypic.com/1428m5x.jpg
http://i46.tinypic.com/2a5kuvq.jpg
http://i45.tinypic.com/2mfme0m.jpg
(NOTE: Remember to bleed you clutch :goodjob:)
What you will need: (Part numbers are from Summit Racing)
(1) pair Male -3 AN to Male 10mm x 1.0 Earls Brake Adapters EAR-592032ERL ($14.69)
http://i46.tinypic.com/34i21qp.jpg
(2) steel -3 AN swivel hose ends. Style is up to you.
I used 1 regular hose end - AER-FBM1100 ($5.25) &
1 45deg hose end - AER-FBM1110 ($10.25)
http://i49.tinypic.com/2q1thc6.jpg
(1) -3 AN braided hose 10ft length. EAR-610003ERL ($29.95)
http://i48.tinypic.com/rac7d2.jpg
(NOTE) You probably wont need 10ft of the hose (I only used bout 4 or 5ft.) but Summit was sold out of 6ft so I just got the 10ft :goodjob:
(1) DOT 3 brake fluid - any qty/brand should work
THE INSTALL
Take a 10mm wrench and unscrew the fitting like so..
http://i47.tinypic.com/nx1k0g.jpg
http://i45.tinypic.com/t6oxhi.jpg
Install the new 10mm fittings. (NOTE: That notch of the block may get in your way a little but not so bad to where it wont screw in the threads. Just make sure you get it started good)
http://i49.tinypic.com/14ad1dh.jpg
I then mapped out where I wanted to run the line. I wanted easy access to it so I just ran it over the top of the tranny back behind the T Bracket, behind all the hardline brakelines and over the brake booster.
I had a lot of excess hose so I tapped off where I wanted to cut it and used a punch and hammer to cut it like so..
http://i45.tinypic.com/ka61yd.jpg
Install the braided hose to the hose ends. Check this link (http://www.anplumbing.com/SWIVEL_SEAL_HOSE_ENDS.html)for install instructions.
http://i48.tinypic.com/246mmwl.jpg
http://i50.tinypic.com/fp8rhw.jpg
Then just run the line where you want it and hook up the hose ends and VOILA!
http://i48.tinypic.com/1428m5x.jpg
http://i46.tinypic.com/2a5kuvq.jpg
http://i45.tinypic.com/2mfme0m.jpg
(NOTE: Remember to bleed you clutch :goodjob:)