FS: GANGSTER 2.0l LSVTEC*278HP 230+whp READY TO GO*

[Vteckidd]

This was my backup motor for my CRX, decided to go in a different direction, so i have no use for this anymore.

Let me state this is not some bullshit halfassed built motor. THIS IS A PROFESSIONALLY ASSEMBLED LONGBLOCK from DFE ENterprises. DFE was the shop that built my old 2.0l motor that made 264BHP(237whp).

Motor Specs:
Skunk2 PRO3 PROTOTYPE Camshafts
Skunk2 PRO Valvetrain
Skunk2 PRO Camgears
CP Pistons 12:1
Eagle Rods
DFE Ported Cylinder head
BRAND NEW ITR HEAD
B20 Short block
ACL Race Bearings
GE LSVTEC Oil Line/conversion kit
ARP Headstuds
DFE Crank Scraper (doubt anyone in atlanta has this)
NEW: ITR Oil pump, ITR head gasket, cam seals, timing belt, water pump, etc

Motor has 40 ENGINE DYNO PULLS so it is fully broken in ready to rock and roll.


FULL LONGBLOCK with Skunk2 PRO intake manifold and 70mm TB $3000 FIRM


PART OUT PRICES:
Shortblock PROFESSIONALLY ASSEMBLED with 0 miles $2000
ITR Cylinder head ported PROFESSIONALLY with mile with Skunk2 Valvetrain $1000
Skunk2 PRO3 cams $450
Skunk2 PRO Cam Gears $140


If you drop this motor in your car it will make north of 230whp which would put you in the top 3 NA B Series in the state.

[Vteckidd]

The PRO3s are prototype cams, they are the ONLY SET IN THE COUNTRY. These were sent to me for testing before they ever made the production set and have different specs than the production PRO3s.

I will upload the dyno chart in a min

[RBS]

nice

[NoWAyItZTOMmY]

damnn

its b20-vtec not ls-vtec, lol. just yankin your chain

[Vteckidd]

true, i was used to my old motor which is a LS Block.

b20vtec fo sho

[Benefit]

bump

[lcortes32]

wow sick setup...I wish i had that cash laying around

[Vteckidd]

DO NOT BUY---MOTOR WILL BLOW UP

baNNED for sponsor bashing, and my shit doesnt blow up because i actually spend money.

You on the other hand, use garbage ass parts and pass it off as new. My rep speaks for itself

[IntegraXTR]

DO NOT BUY---MOTOR WILL BLOW UP

care to explain?

[Vteckidd]

care to explain?

hes pissed off cause when he tried to sell his ITR car a year ago he told people it had a NEW OEM CRANK NEW RODS NEW NEW NEW NEW everything, when in reality he got called out because it was all used parts, half of it wasnt even ITR.

He didnt tell the whole story about how the motor rod knocked and he slapped a used GSR crank and bearings in the motor and thats why he was trying to sell it.

My motors always make power. I have dyno sheets and like i said, my NA motors have NEVER blown up especially when built by the best people in the industry.

[boosted_nonv]

GLWS Mike, trust me ya'll that motor is legit, somebody needs to by this motor so DiscoMonkey could have some competition at the track cause he kills all you allmotor people lol, drop this shit in a Rex and go at it

[DriVaH]

bump.... that sounds sweet. gl man

[Turbodude06]

Thats a good deal to have one of the top 3 NA B Series in the state. GLWS:goodjob:

[gerardojdm]

Killer set-up!!!! Are there any trades or did i miss that part?

[RotiEatter]

Where is the torque? Finally going H-series? :p

[mieghatch]

nice setup. BUMP

[lcortes32]

GLWS Mike, trust me ya'll that motor is legit, somebody needs to by this motor so DiscoMonkey could have some competition at the track cause he kills all you allmotor people lol, drop this shit in a Rex and go at it
X2

[SpooL'DGsR]

bump for a great guy and seller!!!!! glws....

wow i so remember your black crx like it was yesterday...... that car hauled ass...

[Drag404]

Really nice setup, should sell fast, Itr motors are going for this much and not as fast as this LOL.

[D3UC3S]

good shit mike! whats next my brethren???

If i had the cash i would be all over this

[getherdone]

bump great setup

[112480]

WTF!! Y U SELLING:no:

[miguelvqz]

What ecu u wqs running

[phatdaddy143]

can this motor be for a daily, or just track. i wish u have this when taxes come in jan.

[FasTech]

can this motor be for a daily, or just track. i wish u have this when taxes come in jan.


Its 12:1 so yeah it would be fine for a street/track motor. Just use 93 octane.



GLWS, brosky... Wish I had the cash for this. Could use it in my Da project.

[Vteckidd]

WTF!! Y U SELLING:no:

Just decided I'm happy with the itr motor . It runs too good to take it out. I'm gonna leave it

[USA_EK9]

OKAAYYY!!!! where's the pic!!!

[marcos713]

Bump for bad ass setup!! Who ever buys this is gona be owning all over! GLWS man

[STRteg]

damn wish I had cash for it glws

[Black R]

that's a hell of a deal imo.

i've spent more than that on just machine work and headwork! :/

[bernard]

This is a good deal here. Don F have high reps everywhere. Glws

[DustnU]

Very nice price and set up. Would be a great addition to my fully gutted Cx. Hmmmmm. bump

[wrekonize]

does it come with a tuned ecu for this setup.......just curious

[Vteckidd]

No it doesn't but Scotty tuned my last 230+ motor he can tune this. All you need is a chipped ecu (Crome/hondata)

it's perfectly streetable

[wrekonize]

waiting on some cash to come thru if so ill shoot you an offer

[JDMGRNAV6]

badass shit

[southside]

Man this is a piece of shit motor GTFO of here



















LOL JK why you selling this and why so cheap thought this was going in the rex.

[Starrfire]

That is a pretty good deal, bump

[Da_unknown]

g/l mike :goodjob:

[NoWAyItZTOMmY]

Ballin'!!

[ash7]

This was my backup motor for my CRX, decided to go in a different direction, so i have no use for this anymore.

Let me state this is not some bullshit halfassed built motor. THIS IS A PROFESSIONALLY ASSEMBLED LONGBLOCK from DFE ENterprises. DFE was the shop that built my old 2.0l motor that made 264BHP(237whp).

Motor Specs:
Skunk2 PRO3 PROTOTYPE Camshafts
Skunk2 PRO Valvetrain
Skunk2 PRO Camgears
CP Pistons 12:1
Eagle Rods
DFE Ported Cylinder head
BRAND NEW ITR HEAD
B20 Short block
ACL Race Bearings
GE LSVTEC Oil Line/conversion kit
ARP Headstuds
DFE Crank Scraper (doubt anyone in atlanta has this)
NEW: ITR Oil pump, ITR head gasket, cam seals, timing belt, water pump, etc

Motor has 40 ENGINE DYNO PULLS so it is fully broken in ready to rock and roll.


FULL LONGBLOCK with Skunk2 PRO intake manifold and 70mm TB $3000 FIRM


PART OUT PRICES:
Shortblock PROFESSIONALLY ASSEMBLED with 0 miles $2000
ITR Cylinder head ported PROFESSIONALLY with mile with Skunk2 Valvetrain $1000
Skunk2 PRO3 cams $450
Skunk2 PRO Cam Gears $140


If you drop this motor in your car it will make north of 230whp which would put you in the top 3 NA B Series in the state.



nice engine :goodjob:

...where's the block code?
-jonathan

[RHD_Joe]

Glws

[Black R]

nice engine :goodjob:

...where's the block code?
-jonathan



who cares, it was a pos b20 originally!

[BTEC]

i need to borrow this for a little while to get the spider webs off my hatch. can i rent it for like 50 a week? lmao!!!

Good luck dude.

[Vteckidd]

Will trade for jrsc plus cash

[D3UC3S]

bump for vtec

[NEMO]

bump for you... just dont understand why you would sale it :ninja:

[Vteckidd]

Just don't care to go through with it anymore. My oem motor runs too good

[NEMO]

Just don't care to go through with it anymore. My oem motor runs too good
glws this will be a bad ass all motor. i might have my work cut out for me with the person that gets this

[DustnU]

[quote=NEMO;38524506]glws this will be a bad ass all motor. i WILL have my work cut out for me with the person that gets this

If I can get this you will deff need to get ready, LOL Workin on funds right now.:goodjob:
FIXED, LOL

[Vteckidd]

I'll trade for only the following:

Jdm hydro itr tranny with 4.78fd (you add cash)
jrsc for b16 (you add cash)
b16 cable tranny s1,y1, or ys1 with 4.78 fd

[Vteckidd]

Oh and if it's not sold by end of this week I'll star piecing it out on ht and here so hurry up if you want the whole thing

[getherdone]

someone buy this for there rex or da glws

[uproot]

baller for sure, whoever gets this will not regret it

[LongLiveH2b]

bump for a great seller and buyer!! Everything from him is good!! Dont hesitate people!!

[bends33]

reps on a ballin ass setup and a great seller!

[broncos97]

bump good stuff.

[evogotspray]

bump glws

[teggy1990]

waiting for my stupid ass military bonus of 19000 to come in by the end of this month...

[Vteckidd]

if you really want it better leave me some sot of deposit, im about to part it out

[blown_ss]

you want a itr long block plus cash?

[Vteckidd]

Yes but it would be at least $1000 cash

[Sir_Christopher]

ill give you my whole car for it haha

[jap_racer1]

i just have a ? why does it say over 40 dyno pulls but it says the shortblock has 0 miles on it?

[Vteckidd]

40 engine dyno pulls motor has never been in a car or seen the street so miles technically are zero

[RotiEatter]

Bump for Mike.

[blown_ss]

Yes but it would be at least $1000 cash

to tell you the truth thats what i was thinking. let me see what i can do.:D

[Turbodude06]

to tell you the truth thats what i was thinking. let me see what i can do.:D

vteckidd ^ His is my old motor I mentioned to u about, at the carwash saturday... Its a good/strong motor...:goodjob:

[Vteckidd]

Pro3 cams sold on ht
itr head and valvetrain sold on ht

block is left

[driftuner240]

ill trade u a pair of blk s2k seats and a k20 si head complete just 4 ur itr head

[driftuner240]

sorry i dont know how 2 read

[Vteckidd]

Block is pending sale this week looks like it's all gone