DRFT86
10-31-2009, 03:11 PM
I'm selling my 3tc engine setup from my AE86. Let me start off by saying that if you want something that is reliable,strong, and cheap this is the way to go. I've built 16 valve engines before and spent 3 times as much money as a 3tc build, with more power out of the 3tc. Here is the list of goodies you will get with my complete bolt in swap. Located in Marietta Georgia 30062 Asking 850 for everything listed
3tc engine
Dellorto 40mm sidedraft carbs(all gaskets and seals replaced last year)
3tc Sidedraft intake manifold(think its from BRD not sure)
2.5 inch velocity stacks
Carb filters
Tranny
Mallory fuel regulator
Head was milled (.40)
Block bored over half a mm
Toyota high comp pistons
Cometic metal head gasket
Brand new NGK plugs
NGK wires
Custom exhaust (comes behind the driver wheel)
Custom header(fits perfect around steering rack
IAP Single valve springs(not installed still in box)
264 Degree cam(not sure the brand, awesome around 3800-7500)
TRD clutch
Lighten flywheel(not sure brand)
Driveshaft
Custom motor mounts and tranny mount
radiator and hoses
Get the carbs tuned to your personal agenda, put good oil in it, and drive this thing anywhere you want. This will not by my last 3tc engine I will say. This is a great setup. If you have any questions feel free to message me, email me or text me. Thanx for looking hope you like.
[email protected]
number-6783657391-june is the name
http://i94.photobucket.com/albums/l89/DRFTroku/1031091526.jpg
http://i94.photobucket.com/albums/l89/DRFTroku/1031091527.jpg
http://i94.photobucket.com/albums/l89/DRFTroku/1031091527.jpg
http://i94.photobucket.com/albums/l89/DRFTroku/1031091527b.jpg
http://i94.photobucket.com/albums/l89/DRFTroku/1031091528a.jpg
http://i94.photobucket.com/albums/l89/DRFTroku/1031091528a.jpg
http://i94.photobucket.com/albums/l89/DRFTroku/1031091534.jpg
3tc engine
Dellorto 40mm sidedraft carbs(all gaskets and seals replaced last year)
3tc Sidedraft intake manifold(think its from BRD not sure)
2.5 inch velocity stacks
Carb filters
Tranny
Mallory fuel regulator
Head was milled (.40)
Block bored over half a mm
Toyota high comp pistons
Cometic metal head gasket
Brand new NGK plugs
NGK wires
Custom exhaust (comes behind the driver wheel)
Custom header(fits perfect around steering rack
IAP Single valve springs(not installed still in box)
264 Degree cam(not sure the brand, awesome around 3800-7500)
TRD clutch
Lighten flywheel(not sure brand)
Driveshaft
Custom motor mounts and tranny mount
radiator and hoses
Get the carbs tuned to your personal agenda, put good oil in it, and drive this thing anywhere you want. This will not by my last 3tc engine I will say. This is a great setup. If you have any questions feel free to message me, email me or text me. Thanx for looking hope you like.
[email protected]
number-6783657391-june is the name
http://i94.photobucket.com/albums/l89/DRFTroku/1031091526.jpg
http://i94.photobucket.com/albums/l89/DRFTroku/1031091527.jpg
http://i94.photobucket.com/albums/l89/DRFTroku/1031091527.jpg
http://i94.photobucket.com/albums/l89/DRFTroku/1031091527b.jpg
http://i94.photobucket.com/albums/l89/DRFTroku/1031091528a.jpg
http://i94.photobucket.com/albums/l89/DRFTroku/1031091528a.jpg
http://i94.photobucket.com/albums/l89/DRFTroku/1031091534.jpg