PDA

View Full Version : 97 Civic Clutch Pedal Assembly In A 95 Civic?


streethondar
09-10-2009, 05:45 PM
Will a 97 Civic Clutch Pedal Assembly Fit In A 95 Civic? I got the clutch pedal in and it fit prefect! Its just the lines i am having an issue with routing. Any help would be great! I have a photo of my Clutch Assembly if needed!

Thanks
StreetHondaR
Barefoot
09-10-2009, 06:08 PM
ive never tried to switch them out. my roommate says they are almost the same. he isnt sure the difference nor am i.
streethondar
09-10-2009, 06:10 PM
ive never tried to switch them out. my roommate says they are almost the same. he isnt sure the difference nor am i.

The pedal and everything mounted right in. see my car was an auto but they did a 5-speed swap on it and then i bought the body of the car after they pulled the motor and the clutch pedal out and stuff out. So its now setup for a 5-speed and i am rebuilding it i just about got all my parts. I put the pedal in and all. Just cant seem to fig out where to mount my lines.
Barefoot
09-10-2009, 06:13 PM
ooo got yah that i cant tell ya off head.
streethondar
09-10-2009, 06:19 PM
ooo got yah that i cant tell ya off hand.

Here is a photo of the exact pedal and all im putting in my car it came off a 97 civic.

http://www.gurumaniacs.com/pedal.JPG
streethondar
09-10-2009, 06:27 PM
As far as i can tell i could do steel braided hoses if needed to route my lines. but these lines will mount it.. i just dono how... gone stupid today...
streethondar
09-10-2009, 06:46 PM
DUH ME!!! the lines dont mount on the body....... they mount on the engine/tranny.. DUH!!

http://www.k20a.org/forum/showthread.php?t=6813
Barefoot
09-10-2009, 06:51 PM
your bad at describing issues. i would have just said where do the lines mount.
streethondar
09-10-2009, 06:53 PM
your bad at describing issues.

How so? i thought i said it plain as day comes.
yellow ek
09-10-2009, 11:24 PM
Are you doing a K swap? The link you posted is for a K swap which is totally different. For a B series the line will run across the firewall down the frame rail and across the transmission. The 96-00 mount differently. I believe Integra lines are the same as 92-95 civics. The 97 line should reach I just don't know how many places it will bolt up.
streethondar
09-10-2009, 11:25 PM
Are you doing a K swap? The link you posted is for a K swap which is totally different. For a B series the line will run across the firewall down the frame rail and across the transmission. The 96-00 mount differently. I believe Integra lines are the same as 92-95 civics. The 97 line should reach I just don't know how many places it will bolt up.

No, i am doing a D16A swap.
yellow ek
09-10-2009, 11:32 PM
No, i am doing a D16A swap.

Ok, that line in the link is too short. You can do a set up like that but it will need to be longer, or if you want it to be 100% stock look for the 92-95 civic or 94-01 integra line and brackets. If you just need to get it running, you can run the line you have, but it will look crappy because it won't bolt up.
streethondar
09-10-2009, 11:35 PM
Ok, that line in the link is too short. You can do a set up like that but it will need to be longer, or if you want it to be 100% stock look for the 92-95 civic or 94-01 integra line and brackets. If you just need to get it running, you can run the line you have, but it will look crappy because it won't bolt up.

What about ordering a braided clutch line? run it form the master to the salve?
yellow ek
09-11-2009, 08:07 AM
What about ordering a braided clutch line? run it form the master to the salve?
http://cgi.ebay.com/ebaymotors/Russell-civic-integra-5-sd-conversion-clutch-line-kit_W0QQcmdZViewItemQQ_trksidZp3286Q2ec0Q2em14QQha shZitem27ab8a8c84QQitemZ170381708420QQptZMotorsQ5f CarQ5fTruckQ5fPartsQ5fAccessories
Yes, here is what you need, from ebay.