LT1 6 speed Z28

[Catnip]

CAI, exhaust, and clutch

Dunlop shitty ass tires. Spun all of first and most of second and third (not chirping/barking)... on this run. Other runs 13.8, 13.9, and 14.0, all spinning ALL of the first 3 gears and the 14.0, spinning fourth.

http://i55.photobucket.com/albums/g146/84_318i/DSC00151-3.jpg

Over all just a shitty track tonight. Pretty sure it wasn't prepped once. But the car ran strong @ WOT. Can't say much for any other time, lol.

[Revmaynard]

What should it be running with proper tires/driving?

[Catnip]

Driving was spot on for the conditions.
But with some good drag radials, should do a 13.3-13.5 :)

[Evil Goat]

Over all just a shitty track tonight. Pretty sure it wasn't prepped once. But the car ran strong @ WOT. Can't say much for any other time, lol.


might just be a shitty driver because i cut pb's....again! :D

[Catnip]

might just be a shitty driver because i cut pb's....again! :D

lol. Let me get some DRs ;)

[Evil Goat]

lol. Let me get some DRs ;)


lol, true, it aint fair on full slicks to say the track wasn't prepped :D

[Catnip]

lol, true, it aint fair on full slicks to say the track wasn't prepped :D

AND only run 10's :taun:







jk man. Congrats on it! Feel good to finally hit it?

[03RCode]

Weaksos 60', Weaksos driver.

[Evil Goat]

AND only run 10's :taun:

jk man. Congrats on it! Feel good to finally hit it?


lol, no doubt man, been a long time coming...

[JJSPEC Racing]

It was prepped nicely last night. After Evil Goats burnout you could hear the tires just grabbing all the way to the tree. Those were some pretty good et's on street tires, catnip. Cant wait to see what it does with some better tires on the back. I may have some drag radials that still have life left in em.

[Catnip]

It was prepped nicely last night. After Evil Goats burnout you could hear the tires just grabbing all the way to the tree. Those were some pretty good et's on street tires, catnip. Cant wait to see what it does with some better tires on the back. I may have some drag radials that still have life left in em.

Do tell on the drag radials :D

[Motivation]

Very nice, Evan.

[Tech5]

man my civic can run better then that!

[pimpdaddy]

Are the computers tuneable in those cars?

[Slomaro Z28]

yes (obd2), but not everyone has LT1 edit.....they can be chipped or hand held also.

[quicksix]

Get that 60' down and you will see better times :goodjob:

[Catnip]

Got the '60 to 2.0 and ran a 13.3 ;)

[OnURleft]

Pretty nice, looks like you need some slicks with that torque. Probably good for 13.1-13.4@104-105 with those time. My E36 ran 13.9@101 completely stock on shitty tires at SDR in cold weather. Luckily it didn't have enough power to need slicks but I did pull a 2.01 60ft so a 1.8 may have taken it 13.6@102

[Catnip]

Pretty nice, looks like you need some slicks with that torque. Probably good for 13.1-13.4@104-105 with those time. My E36 ran 13.9@101 completely stock on shitty tires at SDR in cold weather. Luckily it didn't have enough power to need slicks but I did pull a 2.01 60ft so a 1.8 may have taken it 13.6@102

Got it on some better street tires and did this :goodjob:

http://i55.photobucket.com/albums/g146/84_318i/DSC00098-3.jpg

Still haven't had a cold, crisp night to take it out... I think on a cold night with slicks and good launch, it'd do a 12.999999999999

[hondalover00]

horrible 60ft time for v8

[On_Her_Face]

I don't think i can pull a 2.0 on street tires, I have done a 2.1 once or twice but usually a 2.2


horrible 60ft time for v8

Let's see you do it boss man. It is a little harder when you have TQ above 50ft/lbs

[SlenderEG6]

Got it on some better street tires and did this :goodjob:

Still haven't had a cold, crisp night to take it out... I think on a cold night with slicks and good launch, it'd do a 12.999999999999

well ur almost in my league.... but not quite! russle ext ftw! :bump:

[Catnip]

well ur almost in my league.... but not quite! russle ext ftw! :bump:


That pretty little mustang? lol. I did a 0-120 pull from lake joy to tharpe (that stretch of Russell), did good... think I can roll run some REALLY high 12 cars and keep up. I get decent traction doing like 10-20 rolls.

Billy, I got a 2.0 60' but it kind of bogged because I didn't launch it high. I think a 1.9 might be possible.

[Lankhoss]

I don't think i can pull a 2.0 on street tires, I have done a 2.1 once or twice but usually a 2.2



Let's see you do it boss man. It is a little harder when you have TQ above 50ft/lbs

You talking about in the Vette?

[SlenderEG6]

That pretty little mustang? lol. I did a 0-120 pull from lake joy to tharpe (that stretch of Russell), did good... think I can roll run some REALLY high 12 cars and keep up. I get decent traction doing like 10-20 rolls.

Billy, I got a 2.0 60' but it kind of bogged because I didn't launch it high. I think a 1.9 might be possible.

well i finally burned the rest of the meat of my radials! thinkin bout tryin a different tire! but wen i do ima be ready to scratch you off my list! lol:D

[OnURleft]

Honestly your doing 13.3 with a 2.0 60ft, I pulled a 13.6@103 with a 2.01 once I modded my car and went 13.4@104 with a 1.94 that same night. There is no reason why that car shouldn't be able to pull a 1.7 or better with the right tire set up. Every .1 off your short time is normally .2 off your E.T. So, you do the math

[Catnip]

Honestly your doing 13.3 with a 2.0 60ft, I pulled a 13.6@103 with a 2.01 once I modded my car and went 13.4@104 with a 1.94 that same night. There is no reason why that car shouldn't be able to pull a 1.7 or better with the right tire set up. Every .1 off your short time is normally .2 off your E.T. So, you do the math


I won't tell you you're wrong because I honestly don't know, but I'm not too sure if it could pull a 1.7... maybe a 1.8. But I've dropped the 60' .2 and the ET .4 ;)

Either way, I agree it could do better on the same setup :D

[Jenson]

Radials+4.10's and you should be able to cut 1.6's. Nice time though from the ole LT.

[Catnip]

Radials+4.10's and you should be able to cut 1.6's. Nice time though from the ole LT.


I don't rev high enough for 4.10s :( It'd put me in 5th gear before the 1/4. Now with the 3.73s, I can stay in 4th till about 118.

[japan4racing]

I don't rev high enough for 4.10s :( It'd put me in 5th gear before the 1/4. Now with the 3.73s, I can stay in 4th till about 118.

that sucks ass....i read earlier that 4.30's are good to 120mph in 4th in 03/04 machs

[xdavidscenex]

your 8.6 in the 1/8 is weak evan.

[Catnip]

your 8.6 in the 1/8 is weak evan.

My civic was only doing 8.50s with SLICKS ;)

[Catnip]

that sucks ass....i read earlier that 4.30's are good to 120mph in 4th in 03/04 machs


Very true, but they're not six speed, right? If so, you have no 6th gear to cruise in :taun:

[japan4racing]

true im just 5 speed.....a t56 can solve that:ninja:

[Catnip]

true im just 5 speed.....a t56 can solve that:ninja:


But then you can't ball on some 4.30s :(

[japan4racing]

who needs 4.30's anyways?

[Jenson]

You should be able to get about 116 out of a 28" tire and 4.10's. 3.73's just are not worth it in a 3.42 car. Unless yours is the older 3.23?

[xdavidscenex]

My civic was only doing 8.50s with SLICKS ;)


my 197whp civic only went 8.1 with slicks.:???:

[Catnip]

You should be able to get about 116 out of a 28" tire and 4.10's. 3.73's just are not worth it in a 3.42 car. Unless yours is the older 3.23?

I don't rev as high as LS1s and my car is way underpowered/underequipped for 28" slicks... lol

[03RCode]

who needs 4.30's anyways?



IMO a Mach should have came from the factory with 4.30's :goodjob:

[03RCode]

I don't rev as high as LS1s and my car is way underpowered/underequipped for 28" slicks... lol


You just need to throw a set of 26x10.50 slicks, and a 200 shot on it you pansy.

[Catnip]

IMO a Mach should have came from the factory with 4.30's :goodjob:



We're talking about Ford, lucky they don't come with 2.73s... lol

[03RCode]

We're talking about Ford, lucky they don't come with 2.73s... lol



Mach + 4.30's + Good DR's = :goodjob:


LT1 + 3.73 + 26x10.50 + 200 shot = :goodjob:

[Catnip]

Mach + 4.30's + Good DR's = :goodjob:


LT1 + 3.73 + 26x10.50 + 200 shot = :goodjob:


125 is the biggest I'd do on the stock motor. lol

[03RCode]

125 is the biggest I'd do on the stock motor. lol



Hey Evan...


Hey Evan...


Your vaginas showing.

[Catnip]

Hey Evan...


Hey Evan...


Your vaginas showing.


:lmfao::lmfao:

[Logan]

Your trap speed is pretty nice. Shows you have more left in the car.

[HypnoToad]

We're talking about Ford, lucky they don't come with 2.73s... lol

Fbody automatic gear FTL 2.73 ewww

[Jenson]

Gay, you have a 2.73 car? 3.73+26" will still be about 118 max in fourth.
Heres a link just incase you want to check it out.

http://www.f-body.org/gears/

[Catnip]

Gay, you have a 2.73 car? 3.73+26" will still be about 118 max in fourth.
Heres a link just incase you want to check it out.

http://www.f-body.org/gears/


I've spent countless hours on that site :lmao:

I have a 3.42 OE car, but now has 3.73s.

[Jenson]

I figured so. Sweet, new times coming soon? I really need a windshield so I can just go see what kinda mph my car will run, but I gotta finish the civic first.

[Catnip]

I figured so. Sweet, new times coming soon? I really need a windshield so I can just go see what kinda mph my car will run, but I gotta finish the civic first.


I really need tires, but probably just going to work around them... lol. We did a 20 pull last night and I spun till probably 55-60.

[pimpdaddy]

LOL I have a friend that ran 29x10.5 M/T's on a stock 99 musatng gt with a 175 shot with 175k on the orig motor and it somehow never broke and ran a best of 12.6

[DustnU]

Not bad runs for a crappy track. Gonna be in that range soon, maybe we can run sometime.

[Dwisforme05]

it was too bad we never could meet to run em. hopefully this spring we will be able to. i should have my driveshaft/slicks in by then. im hoping for mid-low 12s