View Full Version : FS: GSR Tranny, Eibach Springs, Megan Tie Bar
bafbrian
05-13-2009, 01:10 PM
I recently got audited by the good ole IRS and need to sell a few items to make up for the dent.
All prices are OBO, meaning they are not set in stone.
GSR Hydro Tranny (3rd grinds) $375
http://i39.tinypic.com/3466hdg.jpg
Vin
http://i44.tinypic.com/10wl6s4.jpg
Tranny Code
http://i39.tinypic.com/sdlcn9.jpg
Eibach Pro-Kit Springs for 96-00 Civic (1.5" drop / used for about 3 months) $125
http://i41.tinypic.com/105xqc6.jpg
Megan Rear Lower Tie Bar for a 96-00 Civic (never used) SOLD
If you don't like the price, then make an offer, worst I can say is no.
Easiest way to contact me is through PM.
Type-Rboost
05-13-2009, 01:58 PM
WATS CAR IS THE TIE BAR FOR?????
Okie_doke.
05-13-2009, 08:32 PM
ilike the tie bar will it fit an ej?
bafbrian
05-15-2009, 11:03 PM
bump
Pikachu
05-15-2009, 11:22 PM
i take that rear low tie bar if u still have it
bafbrian
05-17-2009, 10:37 PM
All pm's replied.
bafbrian
05-25-2009, 11:10 AM
ttt
VickNotic
05-25-2009, 12:46 PM
the gsr tranny it grinds in 3rd but any other problems with it ... liek poping out of gears or .. just grinding.. ?
KevinT707
05-25-2009, 06:30 PM
PM me the lowest you'll go on that tranny.
etank82
05-25-2009, 08:40 PM
PM'ed...
bafbrian
05-26-2009, 11:30 AM
the gsr tranny it grinds in 3rd but any other problems with it ... liek poping out of gears or .. just grinding.. ?
You are correct. If it wasn't for the grinding 3rd, I would have kept it in the car. Got_Purp can vouch for the fact that I had trouble shifting it into 3rd.
marcos713
05-29-2009, 01:14 AM
pm'd
bafbrian
05-30-2009, 10:10 PM
pm'd
All PM's replied
etank82
05-30-2009, 10:41 PM
PM'ed...
bafbrian
06-01-2009, 10:50 AM
Megan Tie Bar pending to Pikachu
driftingkid
06-01-2009, 11:15 AM
What were the springs on?
bafbrian
06-01-2009, 01:39 PM
What were the springs on?
They are for a 96-00 Civic.
Megan LTB SOLD
bafbrian
06-06-2009, 09:53 AM
ttt
-S Double C-
06-06-2009, 04:47 PM
is it hard to get the tranny into 3rd?
bafbrian
06-08-2009, 08:57 PM
is it hard to get the tranny into 3rd?
I only had trouble when I was shifting at high rpm's. Other than that, I didn't have any difficulty with it.
-S Double C-
06-08-2009, 09:37 PM
was it hard to going into gear? it would be going in a 600whp car shifting at 9500
rockit
06-10-2009, 07:19 AM
still have springs?
bafbrian
06-16-2009, 07:24 AM
still have springs?
I still have them. My modem crapped out and I have been waiting on a new, hence the delay in a response.
seanrg1116
06-16-2009, 09:43 AM
any trades for springs?
bafbrian
06-20-2009, 05:51 PM
ttt
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.