View Full Version : DOHC head on a SOHC block?
Curbow_USMC
08-15-2005, 11:50 PM
:confused: just out of curiosity. is there anyway for a DOHC head to fit on a D16y7 block?
i dont think it will but what the hell :bigok:
Curbow_USMC
08-16-2005, 03:26 PM
:wtf: i know this is an off the wall question but somebody say something lol
threehundred
08-16-2005, 03:37 PM
no
Vteckidd
08-16-2005, 04:49 PM
no way in hell
no way in hell
i think that about answers it. lol!!
Curbow_USMC
08-16-2005, 05:23 PM
lol, ok, i was just makind sure. i thought so. some RICER told me that you could do it. i just laughed at him and said, " YEA OK!!!" :jester:
Curbow_USMC
08-16-2005, 05:25 PM
(typo) making*
flysi00
08-16-2005, 08:38 PM
lol
Blaze the chemi
08-17-2005, 06:01 PM
The D series is a SOHC engine. The B, K, and H series have DOHC. As far as I know there is no way in hell to mix a head with one series and put it on another series block. I had a ricer once tell me you can't put a GSR head on a B16, but you can put a ITR head on a B16. Ricers need to change a few more things than the rear lights to Altezzas. HAHA!
Curbow_USMC
08-17-2005, 06:19 PM
:lmfao:
iNsTuN nOoDoH
08-17-2005, 07:06 PM
i believe there's a d series motor that's actually a dohc. I think it's an obd0 motor that you could put a dohc head on, but that's only cuz it was dohc to begin with. maybe i'm wrong...
Curbow_USMC
08-17-2005, 09:10 PM
yea, the only one i know you can do it to is the ZC motor
sir2hb
08-29-2005, 10:01 PM
yea, the only one i know you can do it to is the ZC motor
Yea the zc that came in the older models is a dohc but I dont know if it will bolt to the d model motor
LS2ner
08-29-2005, 11:09 PM
good sir!
Please do with your original idea and have vteckidd build your engine! Your repetitive ideas are boggling me! =P
Curbow_USMC
08-30-2005, 12:16 AM
if you are talking to me i am about to buy a turbo for my y7 and this post is kinda old and is was only posted for some shits and giggles.
LS2ner
08-30-2005, 01:46 AM
you letting vteckidd tune and everything? What set-up did you end going with?
htchking
09-03-2005, 11:33 AM
yea the zc should bolt right up
Theres a guy who did some custom work a put a zc head on a d15 block I believe. Its on honta tech somewhere.
EmminoDaGreat
09-04-2005, 06:37 PM
h22 on f23 block......
Sthrnba711
09-07-2005, 11:24 PM
I know that you can put a F22b which is a DOHC head on any F22. They came in early 90 accords and its not that bad of a swap.
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.