Oil Pan

[JDMB20]

i am not sure how to put a moroso ol pan on my b16some ppl say use hondabond and other say becarefull and g/l

so does any one now how to properly tourqu down the oil pan and in which sequrnce do the bolts have to tightned thanlks in advance

[Barefoot]

8.7 ft.lbs. start from the center and go out. its going to leak no matter what u do from what ive seen so be prepared.

[DeeAOne]

then whats the point paying all that money when it leaks anyway?

[Barefoot]

u tell me

[GSRteg®]

its going to leak no matter what u do from what ive seen so be prepared.


then whats the point paying all that money when it leaks anyway?


u tell me

lirl

[seanrg1116]

:lmfao: :lmfao: good luck man use alot of honda bond

[GsrME]

I had to throw the stock gasket away, and use only black silicone. Moroso pans are great for what they do, buy really crappy for their fitment. Use hondabond or similar and your leak will be gone!

[JDMB20]

alright so i use honda bond and a honda gasket or a felpro gasket? then tourque it to 108.7 ft.lbs or 8.7 ft.lbs ?and i do then center bolts first then go one over and do opposites right ?

[Justin.]

8.7 lol those little bolts can't hold 108.

use a lot of sealant, and fab up a drip pan.

[JDMB20]

alright i will try that and see if it works and will let u guys know

[Barefoot]

question y are u using a moroso oil pan

[JDMB20]

i ahd it on my turbo b16 and when i sold it i took it off and put a stock oil pan back on it so then i put my moroso ol man on my b20 and thats y i am using it yes i have heard stories about iy leaking all th time no matter wat but i have it and would like to use it so if i put it on this time and it leaks then i am going to put the stock pan back on and sell the moroso one

[Barefoot]

i ahd it on my turbo b16 and when i sold it i took it off and put a stock oil pan back on it so then i put my moroso ol man on my b20 and thats y i am using it yes i have heard stories about iy leaking all th time no matter wat but i have it and would like to use it so if i put it on this time and it leaks then i am going to put the stock pan back on and sell the moroso one
get lots of hondabond

[RBS]

get a brand new gasket and slab a nice even coat of High Temp black silicone or Hondabond over both sides of the gasket, then tighten the bolts in a X pattern starting in the center towards the outer bolts to 8-9 pounds of torque... or hand tight with a 3/8 wratchet. if done properly it will NOT leak

[green91]

x2 on the using oem gasket and silicone on both side. i prefer toyota FIPG to hondabond though. I hand snug mine with 12" extension and 1/4" drive ratchet

[JDMB20]

thanks for the help guys....

[mitch lab]

thought the spec are 7.2 ft/lbs on 10mm, because if you torque it too much it's gonna squeeze the gasket outward, and it will still cause a leak.

[JDMB20]

so is it 8.7 or 7.2 ?

[Barefoot]

thought the spec are 7.2 ft/lbs on 10mm, because if you torque it too much it's gonna squeeze the gasket outward, and it will still cause a leak.
alldata say 8.7 and shopkey5 says 8.66666 or 104 in. lb.

[RBS]

i say hand tight... LoL never failed ME

[JDMB20]

Damn oil pans r a b**** if u over tighten it will leak and if u under tighten it will leak.......
and honds r suppost to be easy to work on

[mitch lab]

alldata say 8.7 and shopkey5 says 8.66666 or 104 in. lb.

you are right, just check my book. My apology.

[JDMB20]

its okay we all make mistakes look at me i have to do my oil pan all over agian