PDA

View Full Version : fs/--stroker motor 383



streetstuff
02-24-2008, 08:25 PM
sold

santacruz77
02-25-2008, 12:27 PM
good seller gl with the sale

Complication
03-17-2008, 10:16 AM
I assume it is used? what was it in before? interested possibly...

streetstuff
03-17-2008, 04:32 PM
the block is used it was stock 350 but all the other stuff is new

Nismo
03-17-2008, 07:13 PM
So is this the whole shooting match? Is there a website I can check out to see what I need to throw this in my 97 z28?

streetstuff
03-17-2008, 07:40 PM
you could google it and see but i was told it would fit in anything chev with 350 or 305 i do not know i am a ford man sorry

THEONE
03-17-2008, 07:58 PM
So is this the whole shooting match? Is there a website I can check out to see what I need to throw this in my 97 z28?

it will drop right in. and you need to convert to a carb instead of fuel injection,just put it together and drop it in.you can even use your stock trans.and if its a 5 speed get a good clutch you will need it.

Annihilation
03-18-2008, 11:05 PM
why not just get it tuned and not go carbed

redrumracer
03-20-2008, 08:05 PM
So is this the whole shooting match? Is there a website I can check out to see what I need to throw this in my 97 z28?
itll work but i believe you cant use your heads, ignition, or any of that stuff because i believe your car has an lt series chevy and its reverse flow with the water pump, and your ignition is ran off of the front of your engine. but on the bright side the internals should work in yours.(might want to double check on the crankshaft if itll work)

Blitanicle99
03-23-2008, 11:31 PM
Too bad its not fuel injected... I would be thinking about this...

THEONE
03-24-2008, 08:30 PM
Too bad its not fuel injected... I would be thinking about this...

it could be. with the right heads. a set of vortec heads and the intake from a fi car or truck along with harness and ecu. thats the junk yard route. you can buy a fi kit. but me i like carbs but hey im old so im suppose to.

streetstuff
03-24-2008, 08:54 PM
$1500

streetstuff
03-28-2008, 07:56 AM
trades

dynoman14
04-01-2008, 09:51 AM
Bump it for a good guy and awesome deal !!!

Init2winit
04-02-2008, 06:54 PM
5.7" or 6" rods? Is the stuff balanced? What all was done to the block, and who did the machine work?

jew_boy
04-02-2008, 07:08 PM
man if i had the money or anything to trade i would get this

Blitanicle99
04-02-2008, 11:39 PM
it could be. with the right heads. a set of vortec heads and the intake from a fi car or truck along with harness and ecu. thats the junk yard route. you can buy a fi kit. but me i like carbs but hey im old so im suppose to.


Explain to me how this might work with a 5.3 (LM7) Vortec. Would it bolt together?

streetstuff
04-03-2008, 09:31 AM
5.7" or 6" rods? Is the stuff balanced? What all was done to the block, and who did the machine work?
they are 5.7 rods the block is all done ready to be put together

streetstuff
04-08-2008, 03:22 PM
come on this is a deal