clutch is GONE

[seniosoul]

I gotta 92 Teg. . .i put it in first gear. . .let off the clutch and it won't even stall:eek:. . .first guess is that the clutch is FUUU:idb:EEED. . .someone recommend a sponsor that'll do it for the low or. . .if any of you have a cherry picker for sell (engine hanger) for sell. . .i'll risk sweat, blood and balls to do it myself.:screwy:

[DirtyMechanic]

you dont need a picker to pull the motor to do a clutch just pull the wheels and axles and have at it... you just need a jack so you dont drop it on the ground.

[seniosoul]

DAmn what a relief. . .hahahah. thanks +reps ..
is there a certain procedure to it. . any precautions you can give me.

[DirtyMechanic]

DAmn what a relief. . .hahahah. thanks +reps ..
is there a certain procedure to it. . any precautions you can give me. dont drop it on your foot?... i figure its like any FWD. wheel axles... maybe lower center subframe strap slid trans out on a angle to clear the from frame rail... i deal with nissans and thats how we do it.

[seniosoul]

would i have to replace flywheel and pressure plate also. . .or will replacing clutch fix the problem itself? sorry bout the ?'s they just keep piling.

[DirtyMechanic]

depends on if you cooked the flywheel but i always replace the p-plate with a clutch and throw out bearing

[b16ftw]

chances are it's likely that your flywheel might need to be resurfaced...

and if you were thinking you needed a picker to pull the motor... just to do a clutch.. you might wanna have someone else do it.

no offense.

but really.

[b16ftw]

ohh and as far as choosing another clutch. exedy ftmfw!

[AnthonyF]

I gotta 92 Teg. . .i put it in first gear. . .let off the clutch and it won't even stall:eek:. . .first guess is that the clutch is FUUU:idb:EEED. . .someone recommend a sponsor that'll do it for the low or. . .if any of you have a cherry picker for sell (engine hanger) for sell. . .i'll risk sweat, blood and balls to do it myself.:screwy:

you can buy an engine hoist for like $150 bucks. Or take it to a shop and get it done properly for a few hundred.

[seniosoul]

is it possible to do it without an engine hoist. . .cause i'm not trying to spend money i don't have.

[AnthonyF]

is it possible to do it without an engine hoist. . .cause i'm not trying to spend money i don't have.yea it is. either have a lift and trans jack or take ur chances on trying to lay it on your chest or dropping it on the ground softly.


my .02¢.....let a pro do it.

[DirtyMechanic]

yea it is. either have a lift and trans jack or take ur chances on trying to lay it on your chest or dropping it on the ground softly.


my .02¢.....let a pro do it. he could us a floor jack...

but still if you dont know what your doing. let someone that has done it a few times to either help or do it for you.

[AnthonyF]

he could us a floor jack...

but still if you dont know what your doing. let someone that has done it a few times to either help or do it for you.yea u could but with a...this is a honda right?...that round ass tranny will prob roll over and sqaush him if he doesnt strap it right.

[DirtyMechanic]

yea u could but with a...this is a honda right?...that round ass tranny will prob roll over and sqaush him if he doesnt strap it right. eh yeah dont know hondas. like it said nissan im game

[jadakid88]

i got exedy clutch disc for $40 and ill bring it to you since your immobile

[merfwin]

just gimme ur engine n tranny :)

[RBS]

bring your car to me and ill do a clutch swap for a certain price

[jadakid88]

you should take this deal:D :goodjob:
i got exedy clutch disc for $40 and ill bring it to you since your immobile

[Krappy]

look in the sponsor section. Vuong's Garage Charges $230 starting for labor to replace a clutch... it may be a little more depending on the amount of hours it takes....just check out the sponsor section

[seniosoul]

just gimme ur engine n tranny :)

Since it's my first car and all. . .I'mma ride till it DIE. . .by then i'll hope to have enough money to get another Og teg thats way better:bannana:. . .not possible to become a baller over night all by your lonesome:doh:

Patience is a Virtue :bling:

[GAtegs]

All you need is a basic tool set a good floor jack.

10, 12, 14, 17, 19, 36 mm sockets/wrenches. A few extensions, punch, hammer, etc. Very basic stuff.