96 Spec ITR 4x114.3 Conversion Parts Question

[Dirty Octopus™]

Okay. i made my trip to JHOT on Friday, got my conversion, and now im ready to ball!!! :bump:

Now here's my question for the mere handful of IAers that may have an answer. :rolleyes:

What parts (USDM or JDM) are compatible with my setup. i will have pictures posted later.

i need to know...
in the event i get a stuck/damaged caliper, what can i use?
in the event my Project Mu rotors and pads wear, what can i get to hold me over till i get up the money for a real replacement?

I am well aware of almost every vehicle that has the same bolt pattern but NOT everything fits

thats all i can think of but if there is anything else you guys can think of that i may need to know, please chime in and help a brutha out
:goodjob:

[ash7]

If i am not mistaken, standard DC calipers have the same bolt pattern. However, if you're going to replace just one side... replace the other as well.

-jonathan

[Dirty Octopus™]

If i am not mistaken, standard DC calipers have the same bolt pattern. However, if you're going to replace just one side... replace the other as well.

-jonathan
oh shit! my fuckin' Idol responded! :yay: :bump:

[ash7]

lol, you give me too much credit man.

The only difference in the calipers is the size of the piston. Thus the reasoning for changing out both sides instead of just one.

Project Mu pads up for sale? :)

-jonathan

[Dirty Octopus™]

lol, you give me too much credit man.

The only difference in the calipers is the size of the piston. Thus the reasoning for changing out both sides instead of just one.

Project Mu pads up for sale? :)

-jonathan
nehhh! not for sales :D

http://i200.photobucket.com/albums/aa17/DirtyOctopus/1PICT5481.jpg

[ash7]

...dang :)

sofakingfresh
-jonathan

[bigdare23]

I dont know, but you may be able to rock an Accord rotor.

[Dirty Octopus™]

what about wheel bearings? if needed, what would i be able to use? :thinking:

[00CIVICSI]

take it to napa they can cross and compare that stuff to other honda's.

[speedminded]

take it to napa they can cross and compare that stuff to other honda's.Bet you they don't have the info on a 1996 Honda Integra Type-R though ;) That's exactly what i'm trying to look up right now...

[ash7]

what about wheel bearings? if needed, what would i be able to use? :thinking:

call up hmotorsonline, they'll be able to tell you straight up!

What size axle nut are you running? a 99+ CRV bearing would fit if they are 36mm.

BTW, for ITR's, only the 98+ JDM ITR's have the bigger/36mm axle nut + bigger axle spline. Any pre-97 JDM or pre-01 U.S. Integra-R's, all have the same size 32mm axle nut and end-axle spline size. Hope that made sense...

-jonathan

[Dirty Octopus™]

call up hmotorsonline, they'll be able to tell you straight up!

What size axle nut are you running? a 99+ CRV bearing would fit if they are 36mm.

BTW, for ITR's, only the 98+ JDM ITR's have the bigger/36mm axle nut + bigger axle spline. Any pre-97 JDM or pre-01 U.S. Integra-R's, all have the same size 32mm axle nut and end-axle spline size. Hope that made sense...

-jonathan
damn... why didnt I think of that?!? :thinking:

oh yeah i understood the whole axle nut deal :goodjob:

[NAIZBST]

there are threads on honda-tech, but you can use 92-96 prelude vtec rotors but you will have to put washers to space out the caliper. standard integra gsr pads work and they are basically gsr calipers

[Dirty Octopus™]

okay... Ball Joints (Lower)... can i use any old Integra Ball Joint?

[NAIZBST]

I am pretty sure that you can, the only difference is the actual hub

[.blank cd]

where in the hell is JHOT

[NAIZBST]

where in the hell is JHOT

in August east of atlanta

[00CIVICSI]

its our Jdm whore house. they got awesome price's

[JDMjoe]

^^^^^^^
Nice car LOL

D.O. how much did the setup cost you???