95' Eg Poor Man's Type R build

[TheChosenOne]

Im bored, and I though that I would start a "here's my build thread". So........

I had a pretty nice Hatch/gsr setup that tragically lasted a little more that a flash........................................:(

BUT NOT TO WORRY!!! I have been contenplating for a while which direction I would go: B20/vtec, or ls/vtec, or gsr, or boost, and I decided to build a poor man's type r.

So far, the only thing that has been done is a complete teardown of the front end of my car. We just got the engine and tranny out, and now, we've taken them apart and the bottom end is off to the shop tommorow.

Before:
http://i91.photobucket.com/albums/k292/unuselectus/partingoutpix051.jpg

After:

http://i91.photobucket.com/albums/k292/unuselectus/100_0964.jpg


The block sitting in the back of the Murano

http://i91.photobucket.com/albums/k292/unuselectus/100_0963.jpg


GSR tranny sitting in the garage

http://i91.photobucket.com/albums/k292/unuselectus/100_0961.jpg

My plans are to run a B16 head with ITR cams, AEM adjustable cam gears, aftermarket fuel rail, prelude injectors or 310cc injectors, and a GSR Block with oversized pr3 pistons, gsr rods, and acl race bearings. ** I'm probably going to get a type r fuel pump and fuel pressure regulator.

Thanks for looking... any suggestions and comments are welcome.

[silversol]

now is a good time to scrub the shit out of that engine bay! good luck with your build!

[TheChosenOne]

ya, were gunna clean it up all nice and shinny like!

[Benefit]

jordon you got that cable thing out??

[speedminded]

What size pistons? You can put the K20a2 pistons on the b-series connecting rods for a lil fun ;)

[gtikid]

Wire-tuck FTW!! :goodjob:

[white_rice]

god dam ur intake is lik d size of an andaconda ...lol

[TRDwasiq]

god dam ur intake is lik d size of an andaconda ...lol
its called WHALE PENIS

[kennyboi]

g/l with the build

[GSRteg®]

Very much luck with the build man.

[iloveboost]

FYI: Type R, GSR, LS fuel pumps are all the same after '96.

Good luck on the build. May want to do a wire tuck while you're tearing it apart. Even if it is only a mild job.

[WhiteAccord]

x2 on the wire tuck...

[gtikid]

Hit me up Jordon, i'll let you take a look at how good a mild wire-tuck job looks ;)

[TheChosenOne]

Thanks guys...

Now that you all mention it, I do want to do a wire tuck, but I think i'll need some help with that, cause I'm not really sure what needs to be done. I'll do some research.

2nd.

I got the b16 head in late last night, and on sunday it will be sent out to get a port & polish. I'm going to have to sell my skunk2 manifold thats for a gsr, and buy another aftermarket manifold for the b16 because that stock intake is not going to cut it.

[TheChosenOne]

jordon you got that cable thing out??

lol, we got one off, but we just took the tranny out with one of them still on. We just disconnected it from the shifter.:rolleyes:

[cactusEG]

god luck son.. i bet that shits ganna be fast as fuck too

[TheChosenOne]

god luck son.. i bet that shits ganna be fast as fuck too
...it'll get where it needs to go...:ninja:

I just took out the entire A/C unit, and the engine bay already looks 10 times better.

P.S. The a/c works, so I think i'll sell it!

[TheChosenOne]

Hit me up Jordon, i'll let you take a look at how good a mild wire-tuck job looks ;)
Hells ya... call me or something...numbers in the sig:goodjob:

[Da_unknown]

g/l man if u need an intake manifold i have a skunk2 pro series and an aebs, if u would like one of them lmk..

[Benefit]

take out the power steering shit too!

[TheChosenOne]

take out the power steering shit too!

Don't think I ever had it......vx model.......;)

[gtikid]

A/C and P/S is for pussies :yes:

:(

[2micro4u]

Good luck on the project bro :goodjob:

[spacelion]

:goodjob: Good luck with it, I'll be watching this thread because this is an option for a build of mine.

[cactusEG]

...it'll get where it needs to go...:ninja:

I just took out the entire A/C unit, and the engine bay already looks 10 times better.

P.S. The a/c works, so I think i'll sell it!

pm me a price...

[TheChosenOne]

UPDATE!

First, I took of the radiator. That's about where I started my psudo-wire tuck. I did the right, front corner first. Basically I poped out the wire holders from the chassis and ran it under the wheel well. I did the same thing on the left side, but it was a little more tricky being that I had to run the horn wires with it.
After that, I really couldn't think of anything else to do beside re-route that vacuum hose in the back, under the thing-a-ma-jig. (i'll explain later)

http://i91.photobucket.com/albums/k292/unuselectus/partsforsale2011.jpg

http://i91.photobucket.com/albums/k292/unuselectus/partsforsale2012.jpg

Here is the before and after thing again:

http://i91.photobucket.com/albums/k292/unuselectus/100_0964.jpg

After

http://i91.photobucket.com/albums/k292/unuselectus/partsforsale2013.jpg

I'm really doing this by myself, so if anyone has any techniques or ideas, just shoot me a post. I also removed the battery, but I don't know if I feel like extending the wires to the trunk. I will be taking the alarm out of the bay, aswell as that spare amp wire.

[GSRteg®]

GL on it man....

[Crucial]

You just now work on it bra!!! I'm in LA right now hit me up....

[TheChosenOne]

You just now work on it bra!!! I'm in LA right now hit me up....
Man... I had to wait on people... you know how it goes. But it's kool. As long as my shit is running in two weeks, i'll be straight.

[Benefit]

jordon so where you at in your build now

[TheChosenOne]

jordon so where you at in your build now
Well, I sen't the blcok and the head to be built.

The block is getting a hone job, and then assembled with new pistons and rings, new rod & main bearings, and the stock gsr rods and crank.

The head is getting a match port and polish, new valve seals, and the ITR cams are getting thrown in. It will all be bolted down with arp gsr head studs. (safety first, kids) :goodjob:......

But basically, all i'm doing right now is waiting........................................... .....:cry:

[Repost Squintz]

Well, I sen't the blcok and the head to be built.

The block is getting a hone job, and then assembled with new pistons and rings, new rod & main bearings, and the stock gsr rods and crank.

The head is getting a match port and polish, new valve seals, and the ITR cams are getting thrown in. It will all be bolted down with arp gsr head studs. (safety first, kids) :goodjob:......

But basically, all i'm doing right now is waiting........................................... .....:cry:
waiting sux :no:
but itll be like christmas once you get your shit :yes:

[Da_unknown]

:werd: i see its coming along nicely..:goodjob: