FS: GANGSTER 2.0l LSVTEC*278HP 230+whp READY TO GO*

Quote:

---

Originally Posted by Vteckidd

This was my backup motor for my CRX, decided to go in a different direction, so i have no use for this anymore.

Let me state this is not some bullshit halfassed built motor. THIS IS A PROFESSIONALLY ASSEMBLED LONGBLOCK from DFE ENterprises. DFE was the shop that built my old 2.0l motor that made 264BHP(237whp).

Motor Specs:
Skunk2 PRO3 PROTOTYPE Camshafts
Skunk2 PRO Valvetrain
Skunk2 PRO Camgears
CP Pistons 12:1
Eagle Rods
DFE Ported Cylinder head
BRAND NEW ITR HEAD
B20 Short block
ACL Race Bearings
GE LSVTEC Oil Line/conversion kit
ARP Headstuds
DFE Crank Scraper (doubt anyone in atlanta has this)
NEW: ITR Oil pump, ITR head gasket, cam seals, timing belt, water pump, etc

Motor has 40 ENGINE DYNO PULLS so it is fully broken in ready to rock and roll.


FULL LONGBLOCK with Skunk2 PRO intake manifold and 70mm TB $3000 FIRM


PART OUT PRICES:
Shortblock PROFESSIONALLY ASSEMBLED with 0 miles $2000
ITR Cylinder head ported PROFESSIONALLY with mile with Skunk2 Valvetrain $1000
Skunk2 PRO3 cams $450
Skunk2 PRO Cam Gears $140


If you drop this motor in your car it will make north of 230whp which would put you in the top 3 NA B Series in the state.

---

nice engine :goodjob:

...where's the block code?
-jonathan

Glws

Quote:

---

Originally Posted by ash7

nice engine :goodjob:

...where's the block code?
-jonathan

---

who cares, it was a pos b20 originally!

i need to borrow this for a little while to get the spider webs off my hatch. can i rent it for like 50 a week? lmao!!!

Good luck dude.

Will trade for jrsc plus cash

bump for vtec

bump for you... just dont understand why you would sale it :ninja:

Just don't care to go through with it anymore. My oem motor runs too good

Quote:

---

Originally Posted by Vteckidd

Just don't care to go through with it anymore. My oem motor runs too good

---

glws this will be a bad ass all motor. i might have my work cut out for me with the person that gets this

[quote=NEMO;38524506]glws this will be a bad ass all motor. i WILL have my work cut out for me with the person that gets this

If I can get this you will deff need to get ready, LOL Workin on funds right now.:goodjob:
FIXED, LOL

I'll trade for only the following:

Jdm hydro itr tranny with 4.78fd (you add cash)
jrsc for b16 (you add cash)
b16 cable tranny s1,y1, or ys1 with 4.78 fd

Oh and if it's not sold by end of this week I'll star piecing it out on ht and here so hurry up if you want the whole thing

someone buy this for there rex or da glws

baller for sure, whoever gets this will not regret it

bump for a great seller and buyer!! Everything from him is good!! Dont hesitate people!!

reps on a ballin ass setup and a great seller!

bump good stuff.

bump glws

waiting for my stupid ass military bonus of 19000 to come in by the end of this month...

if you really want it better leave me some sot of deposit, im about to part it out

you want a itr long block plus cash?

Yes but it would be at least $1000 cash

ill give you my whole car for it haha

i just have a ? why does it say over 40 dyno pulls but it says the shortblock has 0 miles on it?

40 engine dyno pulls motor has never been in a car or seen the street so miles technically are zero

Bump for Mike.

Quote:

---

Originally Posted by Vteckidd

Yes but it would be at least $1000 cash

---

to tell you the truth thats what i was thinking. let me see what i can do.:D

Quote:

---

Originally Posted by blown_ss

to tell you the truth thats what i was thinking. let me see what i can do.:D

---

vteckidd ^ His is my old motor I mentioned to u about, at the carwash saturday... Its a good/strong motor...:goodjob:

Pro3 cams sold on ht
itr head and valvetrain sold on ht

block is left

ill trade u a pair of blk s2k seats and a k20 si head complete just 4 ur itr head

sorry i dont know how 2 read

Block is pending sale this week looks like it's all gone